Quantcast
Jump to content

Recommended Lubricants for for my Artic Cat 400 Auto 4X4

CharlieKraynack

By CharlieKraynack
in Arctic Cat ATV Forum

 Share
Go to solution Solved by CharlieKraynack,

Recommended Posts

Gwbarm Grand Master

Gwbarm

Posted
Posted

I think my Eiger has the same 400 engine as your Arctic Cat, this is what I used, not saying its better than synthetic, I used Suzuki Ecstar R5000 10W-40 mineral oil. I also used the compatable suzuki oil filter, and this is why, I went to change the oil and it had a Fram filter, when I pulled the filter it concerned me that there was no oil in the filter, I assumed it had drained back down, maybe the Fram doesn't have a check valve to keep that from happening. Not sure of that I just ordered the correct Suzuki filter.  

Mech Grand Master

Mech

Posted
Posted

That's strange about the filter being dry Gw..  Have you checked it since in case there's a blockage. That filter should be under pressure and so the oil should get through, but some bikes have a pressure bypass that lets oil bypass the filter if it gets too dirty, That bypass valve could be stuck open, or the filter might be causing an air lock..  It shouldn't, but... 

On some manuals they say to undo a bolt in the center of the filter cover and bleed the air and check the oils getting to there after an oil change.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Atomusthenes
      88 Honda four trax 300 4x4
      By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • Coyote251
      2008 Brute Force 650, clutch is slow to engage
      By Coyote251
      I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
      So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem. 
      Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.  
    • Gwbarm
      Trail Tire Valve Replacement
      By Gwbarm
      Have you ever been on the trail and your tire valve goes bad. No way to break down the wheel and replace it. A lot of you probably know about this already i had heard of it but never used one. Just punch out the old one insert and tighten down the nut
       

       

       

       
      So far it has worked very well.
    • Tim Keiper
      2 problems with 2000 Timberwolf 4x4
      By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
    • Gunny
      Sunny Day On The Snow
      By Gunny
      Hope you enjoy the video ....
       
       
       
      ...
       
       

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...