Quantcast
Jump to content


400 cc roketa 4X4 carb problems


Recommended Posts

I have a 400 cc roketa 4X4 that the cvk carb runs gas out the aircleaner . I have reset the float and put a new carb on but it still overflows. It has an electronic plunger on the top of the carb that I don't know anything about so if anyone has had this problem or knows how to repair it ???????

Link to comment
Share on other sites

Does that machine have an electric fuel pump?If it does there might be an issue with the bypass/regulator;causing it to overfill the fuel bowl.That would also explain why it's still doing it after the new carb was installed...Have you checked all the carb vent hoses for blockage?That could also be a cause(I think)

Link to comment
Share on other sites

  • 4 weeks later...
wats wrong with the carb i can prob tell u ghow to fix it :)

1st post Pg 1:wink:

I have a 400 cc roketa 4X4 that the cvk carb runs gas out the aircleaner . I have reset the float and put a new carb on but it still overflows. It has an electronic plunger on the top of the carb that I don't know anything about so if anyone has had this problem or knows how to repair it ???????
Link to comment
Share on other sites

  • 5 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By McG75
      Sorry I suck at these forums so if you see this submitted under update status, my bad. Anyhow this is a new shock for a 96 Yamaha Kodiak 400 4x4 it fits my 96 Yamaha Timberwolf 250 4x4 perfectly. Little narrower are the bottom than the original but everything else is perfect. I extended it to almost a half in from full extension because I’m pushing 350 pounds.  It rides and hold me well. So if any of y'allRace driven shock. have been looking for one and didn’t want to do the research here it is. 





    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...