Quantcast
Jump to content


1984-1985 Tecate kickstarter

coreyschaff13

By coreyschaff13
in ATC 3-Wheeler Forum

 Share

Recommended Posts

coreyschaff13 Rookie

coreyschaff13

Posted
Posted

I recently rebuilt a 84 kawasaki tecate. Everything has went good so far except of the kickstarter. The other day i spent about 3 hours trying to get it to function correctly. It turns the motor over but it wont spring back. I followed the service manuals instructions and still cant get it to work. Spring looks to be in good condition, it is corrrectly placed in the shaft and the case. The plastic bushing is in place with the washer. Any help of info on this would be helpful. Thanks

Link to comment
Share on other sites
ATVmechanic Enthusiast

ATVmechanic

Posted
Posted
I recently rebuilt a 84 kawasaki tecate. Everything has went good so far except of the kickstarter. The other day i spent about 3 hours trying to get it to function correctly. It turns the motor over but it wont spring back. I followed the service manuals instructions and still cant get it to work. Spring looks to be in good condition, it is corrrectly placed in the shaft and the case. The plastic bushing is in place with the washer. Any help of info on this would be helpful. Thanks

Is there a ratchet gear in there? See if the attached diagram helps you out. It's not exactly your year, but I believe the kick start mechanism should be the same.

Link to comment
Share on other sites
coreyschaff13 Rookie

coreyschaff13

Posted
  • Author
Posted

That image is the same diagram that is in my service manual. The rachet gear is fine as far as i can tell. It still manages to turn the motor over just fine. It just doesnt spring back to its home position. In the service manual it tells you to put the kickstart shaft in and lock the sping in the retainer hole in the case and then turn the shaft all the way clockwise... this is to set the preload on the spring im guessing?? I did all this about 4 times. Still doesnt work. The plastic bushing the rides in the middle of the spring doesnt want to stay centered on the shaft all the way. I push it on there as far as i can and make sure the spring is setting on it completely before i put the cover on. When i try and kick it over it stays at the botte and then when i take the cover on the engine again the bushing is not sitting on the shaft the right way.. Is there a trick to this? Im not sure that the bushing is the complete source of the problem either.

Link to comment
Share on other sites
  • 2 weeks later...
mywifeknowseverythin Grand Master

mywifeknowseverythin

Posted
Posted
. Spring looks to be in good condition, it is corrrectly placed in the shaft and the case.

Good morning!!!!

Was this motor running and the kicker working correctly before??? Just curious....

Anyway,,,The spring more than likely has Become weak over the yrs...(24yrs).....

If you need help finding one let me know.....Or,,,,Have you Solved this problem???

Link to comment
Share on other sites
coreyschaff13 Rookie

coreyschaff13

Posted
  • Author
Posted

The kicker worked properly everytime before i tore this engine apart.. Im guessing its something that im not doing right. I havent took much time to look at it since the last post. Ive been trying to gather some info so that i know what to look for instead of just taking it apart and putting it back together the same way over and over agian with the same result

Link to comment
Share on other sites
  • 3 months later...
coreyschaff13 Rookie

coreyschaff13

Posted
  • Author
Posted

Well after about 5 hours of frustrating trial and error i got the kickstarter to work. The problem was that the rachet gear and the shaft werent lined up correctly. According to manual there are a dot on the gear and the shaft and they are suppose to be lined up before assembly to make sure that the preload is set correctly once the shaft is in the case. Well in my special opinon (and dont as me why) with the dots lined up the kickstarter wouldnt work. i had to take the gear off the shaft about 10 times to get the gear placed correctly on the shaft. Works like a charm again.

My next problem is, the machine now starts and idles, but once the throttle is opened up it bogs down and eventually dies out. I have two carbs and one i have went through and cleaned completely(this carb worked perfectly before the machine was torn apart) and a new carb that i have put a new needle and seat, jet needle, needle jet, and floats. i also cleaned the main jet and pilot jet. Both carbs have the same effect on the machine. I have checked the air cleaner thinking that it wasnt getting enough air and was flooding the engine... ran without air cleaner did the same problem.. sprayed carb cleaner into the air filter engine ran the same( i would think it would rev up) and i have checked the reed valves and they are all free. Although i am not an expert on these machines, i have torn this particular one apart enough times that i thought i knew just about everything there was to know about it. I guess not.

If anyone has any suggestions or tips i would definetly appreciate it.

Link to comment
Share on other sites
coreyschaff13 Rookie

coreyschaff13

Posted
  • Author
Posted

i have been doing alot of searching a reading to try and find a solution to this issue on my own, and all that comes up is carb problems (Which i highly doubt is the problem, but i could be wrong), stator/flywheel problems, or muffler problems.

When i had this motor apart the stator and flywheel seemed very good, no rust or oxidation, magnets seemed solid considering they are only glued on. I havent tested the staor with a multimeter at all.

The muffler did spit out a BUNCH of wheat when i started it up(dont remember riding through any wheat in the past) but it pretty much covered the garage floor when i started it up and let it idle. I just dont understand why this would cause the engine to run like this...I understand the concept of backpressure but...idk.

Again.. any help would be appreciate it.

Link to comment
Share on other sites
coreyschaff13 Rookie

coreyschaff13

Posted
  • Author
Posted

ya im going to try runnin it without the muffle and see if that helps it out at all.

To me it seems like its getting too much fuel and not enough air.. Both carbs are stock, with stock jetting. It has a stock size piston and after market silencer.

I have had many carb problems with this thing in the past, but even when it ran like crap, it still ran better than it does now. It wont even wind out enough to get it in gear. The thing starts on the first or second kick and idles good. Like i said it does the same thing with both carbs. Could there be vacuum line on this thing that is causing this?

Is there a possibility that the stator is the problem? There are slots in the stator so it can be rotated about a inch? Could this cause this thing to go from running perfect to barely running?

Link to comment
Share on other sites
DirtDemon Veteran

DirtDemon

Posted
Posted
Well after about 5 hours of frustrating trial and error i got the kickstarter to work. The problem was that the rachet gear and the shaft werent lined up correctly. According to manual there are a dot on the gear and the shaft and they are suppose to be lined up before assembly to make sure that the preload is set correctly once the shaft is in the case. Well in my special opinon (and dont as me why) with the dots lined up the kickstarter wouldnt work. i had to take the gear off the shaft about 10 times to get the gear placed correctly on the shaft. Works like a charm again.

My next problem is, the machine now starts and idles, but once the throttle is opened up it bogs down and eventually dies out. I have two carbs and one i have went through and cleaned completely(this carb worked perfectly before the machine was torn apart) and a new carb that i have put a new needle and seat, jet needle, needle jet, and floats. i also cleaned the main jet and pilot jet. Both carbs have the same effect on the machine. I have checked the air cleaner thinking that it wasnt getting enough air and was flooding the engine... ran without air cleaner did the same problem.. sprayed carb cleaner into the air filter engine ran the same( i would think it would rev up) and i have checked the reed valves and they are all free. Although i am not an expert on these machines, i have torn this particular one apart enough times that i thought i knew just about everything there was to know about it. I guess not.

If anyone has any suggestions or tips i would definetly appreciate it.

Shouldn't the second part of this post be the beginning of a new topic?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • bob2007
      1992 kawasaki bayou 300 KLF300-B5 repairs
      By bob2007
      Hy there great to be able to communicate with people having knowledge I have a continuous problem with a leaking carburetor and I just saw a small rubber hose detached from the bottom of the carburetor and i cannot find were it should be attached and how the two side should be affixed to the carburetor any suggestions as i cannot find a description plan on it thank you Bob
    • Mikey69
      How did you get into Quads?
      By Mikey69
      Heres my story. Kinda long. I guess I was a late bloomer when it comes to quads. I had never ridden a quad in my life. Rode Dirt Bikes as a kid growing up. Back in Oct of '06 I found a Mustang on craigslist. Took it for a test drive one morning before work. Fast car. 351 Cleveland. I had planned on meeting the guy again after work. For some strange reason thats still to this day beyond me, I stopped in Hillsboro MotoSports on the way home from work. I had 6 Grand on me. There was a left over '05 sitting by the front door. It was on sale for $4999. It was $5499 OTD. I didnt even look at anything else. I knew nothing about quads accept I thought it really looked coool and I had the money in my pocket to buy it. I was sitting on it when the salesman walked up and asked... "Can I help you?" Without hestitation I pulled 60 Ben Franklins outta my front pocket and said "I want this Quad. Load it up in my truck." It was just about dark by the time I drove away from the shop. BTW, I didnt bother to ask my ol lady if I could buy it. LOL. Anyway, I took it by the house and showed her. She was kinda stunned but not mad. We drove over to a friend of mines house and unloaded it. I took it to the field across the street from his house. HOLY CHIT!!!!! I was surprised by the power. I had it for about 2 weeks and took it to Sand Lake. I was there a few hours and rolled it on a banked turn at the top of the bowl right before you get to the one-ways. When it rolled, I flew off and landed on my belly. The quad came bouncing and landed on my back. For a month I couldnt even walk. I was scared of it. I considered trading it for a 250EX. Went back to the shop. The salesman said..."Dude!!! You dont want a 250EX!!! Trust me. Just get used to it" I still wasnt convinced. I put it on craigslist for $4000. Calls were coming in. I had a guy that wanted to come look at it that evening. I decided to take it for one last ride at Browns Camp before I sold it. I was still afraid of it. After about 5 minutes I started feeling comfortable on it again. I decided right then, I loved my Honda 450 and would learn how to ride it instead of selling it. That was late Nov of '06. Work was slow for a Painter in Oregon. My new job everyday? Going to Browns Camp and ridding my Quad. I bought my Girl Friend an '02 Blaster. I rode my 450 for 4-6 hours almost every single day for 3 months. And yes, I know my way around Browns Camp pretty well. LOL. In March I bought her an '06 TRX250EX (Thank God I didnt trade my 450 for one of those) LOL Since then, I have become totally addicted to quads. I love them. Couldnt imagine not owning at least one quad. Luckily I have two. My "07 was $6500 OTD in July of '07. Bought it for my Girlfriend. Traded in her 250 EX. A month later we broke up. So, I wound up with two Honda 450's.
       
    • BuckBilly
      The Official Good morning thread!
      By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • justent_88
      94 Kawasaki Mojave 250 - No spark, Very confused
      By justent_88
      Hello, im looking for some input on this situation i have. My 94 Mojave has no spark, and i have no idea what it is. Ive replaced/tested the magneto, the pickup coil, cdi, the ignition coil. Even the key and Killswitch. I haven't tested the harness its self, but i have tried another harness and still nothing. The only thing i can think of is the fly wheel itself. I have found a lot of metal shavings in the fly wheel and have cleaned it the best I could. But nothing happened afterwards. I am truly stumped here and hoping some of yous could shed some knowledge/ideas that could help get this thing to fire. 
    • mga
      good stuff or snake oil?
      By mga
      I see quite a few ads for that  Tribotex additive. It's kind of expensive, has anyone used it it their ATV or any other vehicle?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...