Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Guest Goatman

2005 Arctic Cat 4x4 Axle Replacement???

Recommended Posts

Guest Goatman

:confused:I know I have asked this before but just want to be sure! The axle's do just " pop " out correct? I have never taken one apart before. I tore a boot and toasted the cv joint. I have a slide hammer and will attempt this tomorrow. Does anyone know what a shop will charge to replace one? Sorry its been a long time since I have been on site but with two kids in hockey and construction the way it is did not have the money to mess with it. Hockey is over know but unfortunatly I tore my rotator mucles in shoulder and will be out of work till June. I now have nothing but time to mess with stuff so figured I would get the ATV ready for summer.

Share this post

Link to post
Share on other sites

Guest Goatman

After trying myself gave up. I am not supposed to do anything with my left arm and this was a little to involved to try with one good arm so I took it over to my dads and explained to him what I was going to do. We decided we would wait till tomorrow and that was that. My dad just called me an hour ago and he has it out already. One light rap and it was out!

Share this post

Link to post
Share on other sites

Nice, glad to hear that. Most of the time you can take a small pry bar or large flat head screwdriver, and wedge it between the case and joint. Then edge it out.

What type of ATV was this on?

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

  • Similar Tagged Content

    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
  • Recently Browsing   0 members

    No registered users viewing this page.