Quantcast
Jump to content

Recommended Posts

Posted

Hi there, I just bought a 1989 yamaha breeze 125 for my daughter, and I seem to be blowing plugs after every ride....wondering if anyone knows the correct spark plug i should be using or if anyone has had the same problem?? I dont have the manual,but wondering if the guy i bought it from was using the wrong plug...once i put in a new plug it runs fine for that time then next day need to change the plug again.......thanks carrie

Posted

Caught you again Bot, you double poster you.

Carrie, your Breeze could be fouling plugs for many reasons. Fist thing, obviously, make sure you are using the right plug. If the plug is right, tell us what your bad plugs look like, take a good picture if possible that will help alot.

Posted

Hey there, ok I took some pics of the plug, but I cant seem to upload them...I think my file size is to big...and i have no idea how to decrease the size...if you would like I could email them to you if that helps....but I will describe what it looks like.... When I remove the plug it is very black, not overly wet, but appears to be full of carbon! The plug Im using is an NGK CR7HSA. Thanks.

Posted

Sounds to me like she's running too rich. You might have a fuel mixture screw on the carb that you can adjust. I doubt it was jetted.... Is it all original? Are you getting smoke out of the tailpipe when you are running? If so, is it black?

Posted

I agree, that you are probably running rich, or you are getting some oil in the combustion area. Follow ATV mechcanics' suggestion on the fuel screw, it is probably on the left side of the carb or on the bottom, just to the front of the float bowl. Is your air filter clean? A compression test can tell you alot as well. You should be able to clean those plugs with some fine sandpaper and re-use them. Like Stoopidbot said, an image hosting site makes posting pics easy, I use photobucket myself.

Posted

Hey there, thanks for the info....yes it is all original! No have not noticed any smoke from the tailpipe...my daughter has only driven it a few times.....will check the fuel mixture screw and get back to you.....THanks.

Posted

Good luck, remember to check that air filter, a dirty filter could very well be your problem. I would do that before messing with the carb adjustments. I should have been more clear about that when I posted earlier, sorry.

  • 3 weeks later...
Posted
Hey there, thanks for the info....yes it is all original! No have not noticed any smoke from the tailpipe...my daughter has only driven it a few times.....will check the fuel mixture screw and get back to you.....THanks.

Carrie, how did you make out with this? Any update?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Forum Topics

    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Bobbles
      New to the forum here, hoping someone can help. I have replaced the cdi, coil and sparkplug yet still no spark. The measurements for the igniter and stator are what they are supposed to be, the kill switch is working as it should, the neutral light is working as well. Any ideas where else to look before i start trying to pull it apart for the stator and igniter? 
    • By darklord19991
      We rebuilt the engine put wiring back together it ran before but now it won’t and has a weak spark we have been trying to figure it out for about a week and still nothing changes does anyone have any help on what it might be?
    • By p5200
      I've been using Valvolene 10w 40 ATV oil but, it's like $8.00 a quart. Is that about the going rate? Or is there cheaper alternatives that would be suitable? Thanks
    • By olddude
      Just wondering where you guy's an Gal's get your parts. I love buying OEM stuff but sometimes they just cost to darn much for what they are. I know, I know everybody needs to make a living but dang! $ 97.00 for brake pads on one side of the front of my KingQuad. There has got to be a better way.
×
×
  • Create New...