Quantcast
Jump to content

1998 Polaris Xplorer 400L transmission problem

IndyKWG

By IndyKWG
in Polaris ATV Forum

 Share

Recommended Posts

IndyKWG Apprentice

IndyKWG

Posted
Posted

Hi Everyone, I recently purchased a very used 98 Xplorer 400L. I have had the entire engine rebuilt and that part works great. I've noticed two issues with the transmission. First time out it seems to only top out about 20 to 25 mph. I have replaced the belt and still the same. Second time out same speed issue. Now it doesnt want to stay in gear, high or low. Reverse is fine. First thought was linkage but since its both high and low I wasnt sure if wasnt something more. Then add the slow speed I'm really not sure. I have way too much invested to spend much more. Any ideas are truely appreciated. What type of oil do you run in the transmission on these. Like a dummy I never checked that when I had it all appart. Would a low oil level make it act like that. The thing will pull the front end off the ground at low speeds. Thanks

DirtDemon Veteran

DirtDemon

Posted
Posted

Your centrifugal clutch might not be functioning properly, the oil level or type might hinder some of the tranny functions. I would strongly suggest buying a manual, they are a must have for amyone who is going to be working on their own machines. Until you can get ahold of one, try calling a dealer and talk to a service tech, to see what kind of oil you should use in the tranny.

  • 2 weeks later...
IndyKWG Apprentice

IndyKWG

Posted
  • Author
Posted

adjusted the linkage and added transmission fluid. Shifts very smooth now. I think the top end issue is the high speed jet. I premixed the first tank of fuel and I think its clogged. Something must have shifted on the mounting or something but the linkage took care of it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • AnthonyT
      First time ATV buyer
      By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • Frank Angerano
      My first trailer project.
      By Frank Angerano
      So I decided to pick up a small trailer if I could get one for the right price.  I found this one for a few hundred bucks on Craig’s list.  It is  a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good. 
      I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.  
      I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well. 








    • neilroy87
      1990 Kawasaki Bayou 220 wiring issues
      By neilroy87
      I have a 1990 Bayou 220 that runs pretty well for it's age--needs a new muffler, but sounds tough.    Have had to start with a pull cord since I got it, and recently started troubleshooting the start button.  Finding a lot of information on this issue in the forum, but haven't been able to chase it down yet.  Got a new battery, new starter solenoid, and going to replace the starter relay this week, but not convinced that's going to do the trick, since I can't get the neutral light on when turning the key on.  I can start it by jumping the solenoid, but the 2 black wires to the relay do not activate the starter.  Bad ground or a short somewhere?  Is there a good way to just test the ground?
    • Sportsman500guy
      1996 Polaris Sportsman 500 4x4 Issues with high gear
      By Sportsman500guy
      I bought a 1996 Sportsman 500 4x4 about a month ago, and I love it. Unfortunately, I've been experiencing a few problems with the high-range gear. The first problem is that the gear selector will intermittently pop out of high and into neutral. This problem will sometimes occur when starting from a stop and sometimes will also occur while at cruising speed. The last time this happened I stopped and put it back into gear, however, as soon as I tried to throttle the machine would die. I turned it on again with no problems put it back into high and it died again. Once again I turned it on with no problems put it into low instead and it worked fine with no problem. I drove in low down the road slowly for a little and then shifted back into high with no issues. 
         I plan on working on it this weekend and would just like some opinions or feedback from anyone who may have experienced these problems before. I'm very mechanically inclined but im unsure of exactly where to start as this is the first Polaris ATV that I've owned. Any feedback is appreciated and thanks in advance  
    • Ethan7387
      Quad engine
      By Ethan7387
      Hi could someone please help me, not to sure what engine this is 


COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...