Quantcast
Jump to content

Recommended Posts

Posted

I have a 2005 Arctic cat 500. I got into a little water and the motor died. Fouled the plug.Was gonna try and flush the engine by changing the oil multiple times. After changing the first time and installing new plug the engine still will not fire. ANY IDEAS??

  • 2 weeks later...
Posted

First thing you need to do is figure out what is missing, fuel or spark. Your problem is most likely electrical if it was triggered by something getting wet. If you don't have spark, use a multimeter and start following the power supply to the ignition system and find the opening in the curcuit.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By tepin
      Здравствуйте, нужна помощь по ремонту багги Arctic Cat 700 EFI, пропала искра, датчик коленвала импульс есть, Самодиагностика показывает две ошибки AC99,AC96. все провода проверил на целостность, все датчики блоком определяются, не включается топливный насос. Провода от ECU до реле насоса и от реле до насоса исправны. Поставил подменный ECU, ничего не изменилось.   

    • By digrig
      Hey everyone,
      I’m having an issue with my 2021 Polaris Sportsman 570 – the engine keeps stalling after running for about 10–15 minutes. I’ve checked the air filter, spark plug, and fuel lines, but can’t seem to find the root of the problem. It starts up just fine, but then loses power suddenly.
      Has anyone experienced a similar issue with this model/year? Would appreciate any advice or troubleshooting tips you’ve tried that worked. Thanks in advance for your help!
    • By randyoct
      Will the top end of a 400 fit a 366 the price is so much cheaper
       
    • By joezee13
      After turning off engine in neutral  starter wont engage If I rock unit back and forth it engages Getting progressive worse.
    • By middlebrookgt
      Hi All.  I introduced myself some weeks ago with my 2006 LT-F400F that needed a list of repairs including replacing the cracked generator cover.  It is back together as of last night and cranks up, idles and revs high pretty well.  Needs some fine tuning and stop backfiring at stop.
      The big issue is it will not go into gear.  I reassembled the insides with help from y’all’s posts.  The transfer selector moves from H-L-R, and the foot shifter moves thru the gears and finds neutral easily enough.  Before I tear it back open, the  transfer selector on top does not move as far as the repair manual says.  The diagram shows the shaft moving something like 40 degrees between L and H and 50+ degrees between L and R but it doesn’t move that far even though it finds the indent areas and moves well.  
      Could this be the problem.  I aligned all the dots on the shifter gears inside and it appeared to not be binding anywhere.  I do hear the gears touching when I shift like they are trying to engage, but zero movement from the ARV
      It was somewhat difficult to tell whether all the parts are installed on each shaft.
      Are there better/bigger photos somewhere that would allow me to be confident I included all the washers and bushings, etc?  If I had any doubt on parts that were laying inside after the cover broke then I purchased replacements from online stores.
      TIA for any input or feedback!!  Pics are from when I first took the generator cover off.


×
×
  • Create New...