Quantcast
Jump to content

2007 Arctic Cat 500 LCD Display Problems

jbthunderbird

By jbthunderbird
in Arctic Cat ATV Forum

 Share

Recommended Posts

jbthunderbird Newbie

jbthunderbird

Posted
Posted

Hi I was wondering if I could replace my 2007 500's LCD Display with a 2007 700's display, would there be any problems, would it fit, my 500's LCD display is not working properly only a 1/4 of it is working. I would greatly appreciate any help you can give thinks or any good alternatives

Ajmboy Grand Master

Ajmboy

Posted
Posted

Good question. What I woudl do is call the dealer and see if the connections are the same and teh unit is the same part #.

* Added year, make, and model to your thread title.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Jason39
      Choke problems 2000 Suzuki quadrunner 500
      By Jason39
      I’m having a issue with my choke when its on it runs fine when I cut the choke off the atv cuts off went to take the carburetor off and saw the choke plunger broke at the nut to screw it in could this be my issue? Do I just need to buy a plunger kit and put it on? I took the carburetor off and cleaned both jets anyway just to make sure and it’s still having issues staying on
         
    • Asand211
      1995 Kawasaki KLF220 electric starter not working
      By Asand211
      I've got a 1995 220 Bayou and the electric start does not work.  When I got it the machine was pretty rough but I was told it ran less than a year ago.  The key switch had been cut off and wires  twisted after the key was lost.  I bought a new ignition switch and repaired the wiring and it is working correctly.  It is in neutral and the neutral light is on when the key is turned on but I get nothing when pressing the start button.  I verified there is no voltage going to the starter from the solenoid.  The fuse in the solenoid is good.  Something I found that is odd is that I get positive voltage(12 volts) to the brown, black, and white wires that run into the solenoid when the key is on.  That doesn't make sense to me but I could be wrong.  I would appreciate any help I can get. Thank you in advance.  
    • austinfuller22
      e start problems
      By austinfuller22
      i have a lt 230 and the e start isnt working but i dont know why
      can i have some help
    • TravisCr
      New to the Forum- working a 2003 Polaris Sportsman 700 Twin
      By TravisCr
      I bought this from a buddy to plow snow up in the North Eastern Washington- its been getting oil in the water and I've been changing the oil often and adding collant as necessary-
      I've taken the stator cover off and I'm looking at the Oil Seal and water pump seal and they look good- Although I've ordered a factory oil Seal I'm looking at putting it in this afternoon-
      I don't have the factory service manual- am I suppose to Add RTV to the Stator cover Gasket? I've seen some folks suggest grease other suggest RTV?

      Any suggestions here- I'm trying to reassemble it tonight- I looked at downloading the manual but need to get up to 10 posts firsts it looks like-

      I appreciate any suggestions- normally I'm a jeep and honda dirt bike guy- but  I got a good deal on the quad and a plow so I went for it
      Its got a bit over 3K and runs pretty good- but I've had her tore apart for 3 weeks to figure out the oil in the coolant issue.
    • Tim Keiper
      2 problems with 2000 Timberwolf 4x4
      By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...