Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

thegipper

1987 250 fourtrax parts needed

Recommended Posts



1987 honda 250 fourtrax

Need both front wheel hubs/brake drums!

Can anyone help this neewbie?

Thanks

Sure thing newbie, and welcome. It's not my protocol to promote one forum on another but, in this case, you need to know about the for sale section on a forum that specialized in 250Rs... For Sale

I'm not a 250R guy and I don't know much about that forum other than it's where 250R info is shared and parts are bought/sold/located

Good luck man

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • By jake Stillman
      Hello I am new to this forum and lt80s I have an 87 that has burned up 3 coil/cdi combos my question is can I out the newer set up on it and if so how do I do it I know they have different number of wires going to the cdi mine only has 2 please help
    • By JC4x4
      My Honda Fourtrax won't start. The starter is kicking the engine over, but it won't start. It sat for about a year while I was living away, so I thought it might have been bad gas. I completely drained the fuel, flushed the fuel lines and filled it with fresh gas. However, still nothing. It started and ran fine the last time I used it. Any suggestions on how to diagnose this? It could be fuel or electrical at this point. Is there an easy way to rule one or the other out? Thanks
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By rocky_mtn_honda
      Figured I'd share the wealth with my over 35GB library of shop manuals. Enjoy, and everyone have a very Merry Christmas!
      2005-2009 Honda TRX400EX/400X
      Honda_Trx_400ex_400x_Service_Repair_Manual_2009.pdf
      p/w: trx400ex400x
      2000-2003 Honda Rancher TRX350 TM TE FE FM
      2000-2003 TRX350 TM TE FE FM service.pdf
      p/w: trx350
      2005-2006 Honda Foreman TRX500 FE FM TM
      Honda TRX500FE FM TM Foreman.pdf
      p/w: trx500
      1988-1994 Honda TRX300 Fourtrax, 88, 90-94 TRX300FW Fourtrax 4x4
      Honda Trx_300_Fourtrax_300_Service_Repair_Manual_1988-1994.pdf
      p/w: trx300
      1995-2000 Honda TRX300 Fourtrax TRX300FW Fourtrax 4x4
      http://www.mediafire.com/file/pi0x0w9n84xocc8/Honda%201995%202000%20TRX300%20Service%20manual.pdf
      p/w: trx300
      1985-1986 Honda TRX125 Fourtrax 125
      Honda_Trx_125_Service_Repair_Manual_1985_1986.pdf
      p/w: trx125
      1995-2003 Honda Foreman TRX400FW Fourtrax
      HondaTrx_400fw_Foreman Service Manual 95-03.pdf
      p/w: trx400
      2003 Honda Rincon TRX650FA
      TRX650FA_Rincon650_2003_ServiceManual.pdf
      p/w: trx650
      1997-2004 Honda TRX250TE/TM Fourtrax Recon
      http://www.mediafire.com/file/7cl9nqjedbudo3h/Honda_Recon_Service_Repair_Manual_2004.pdf
      p/w: recon
      Thats a good starter kit...post up your requests in this thread, I have tons more...Hope this helps.
  • Similar Tagged Content

    • By BosoxBruce
      Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
    • By Derick Joel Smith Trimmings
      Buying a Baja 250 tomorrow for 600 bucks, needs nothing but a wheel bearing, i already know Baja is an off brand crappier. Manufacturer, but does anyone have any tips or knowledge of these bikes? 
    • By fatfarmboy
      Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody. 
    • Guest huntingstill
      By Guest huntingstill
      k I would like to take my one person off road go cart and turn it into a sand rail LIFT it new engine and transmission make it so you have to shift w/ a clutch and all the fun stuff a car has
    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...