Quantcast
Jump to content

New From NY!

ThreeFifty

By ThreeFifty
in New Members Area!

 Share

Recommended Posts

Ajmboy Grand Master

Ajmboy

Posted
Posted

Welcome to QUADCRAZY! Fellow NY Stater (was born in the island of Long). What part of NY are you from? I couldn't tell from all the off topic going on ...lol :laugh:

On a side note to stir the pot, LI'ers always feel that they are their own kind and should be their own state...but turn to Albany for $$. If it wasn't for the Hamptons and the draw to go out there by some of the wealthiest, Nassau would be a NYC borough and Suffolk would be "sidestate (instead of upstate...lol)". :laugh: All jokes aside, I love Long Island!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Gtc4d
      need help on a yamaha raptor 80 stalling
      By Gtc4d
      I recently purchased a raptor 80 for my grandson for  christmas. I am trying to make sure it is running properly. i have rebuilt the carb and adjusted the carb idle then the mixture to middle of where it runs rough and it runs great for about a min or 2. then it stalls out. I can usually choke it and it will start so i feel it is lacking fuel. the fuel shutoff valve has been changed and i checked it for good fuel flow.  any ideas of what to check next. I am planning to vfy fuel float height tomorrow. I visually checked it by turning carb upside down when i had it apart and it looked level. any ideas are appreciated. 
       
      Thanks.
      Todd
    • jordan_ATV
      Raptor Pre-ignition?? (Maybe)
      By jordan_ATV
      I got a 2005 350 Raptor Special Edition and I'm dealing with a no start issue; the weirdest thing is when I'm cranking it fires and slows down showing signs of pre firing, smoke shoots out the carburetor every time it sparks. every electrical part (CDI, Rectifier, Stator, Coil) has been swapped out from previous owner, the top end of the engines all new and I cleaned the carb out, anyone got any ideas or similar problems, also is it possible to have a bad spark timing
    • McClaw
      New to the forum
      By McClaw
      Hi Guys, I'm new to this forum.
      I have been riding quads for the last 20 years, however my quads are extremely old and outdated, all three are about 20 years old LOL.
      I have been looking at upgrading, but need your input.
      I've narrowed it down to the Polaris Sportsman XP 1000 S or the Honda FourTrax Foreman 4x4 EPS
      What do you guys think?
       
       
    • TravisCr
      New to the Forum- working a 2003 Polaris Sportsman 700 Twin
      By TravisCr
      I bought this from a buddy to plow snow up in the North Eastern Washington- its been getting oil in the water and I've been changing the oil often and adding collant as necessary-
      I've taken the stator cover off and I'm looking at the Oil Seal and water pump seal and they look good- Although I've ordered a factory oil Seal I'm looking at putting it in this afternoon-
      I don't have the factory service manual- am I suppose to Add RTV to the Stator cover Gasket? I've seen some folks suggest grease other suggest RTV?

      Any suggestions here- I'm trying to reassemble it tonight- I looked at downloading the manual but need to get up to 10 posts firsts it looks like-

      I appreciate any suggestions- normally I'm a jeep and honda dirt bike guy- but  I got a good deal on the quad and a plow so I went for it
      Its got a bit over 3K and runs pretty good- but I've had her tore apart for 3 weeks to figure out the oil in the coolant issue.
    • KdlH
      Hello, I'm new to the forum
      By KdlH
      Hello.
      I'm new to the forum, I live in the UK. I have just bought a 1995 Yamaha Moto 4 350.
      Generally the condition isn't too bad (I paid very little for it!), it looks quite original and all the plastics are quite good. The bad bits are no brakes, the rear axle bearings are shot and the transmission won't shift through the gears properly.
      I'm not planning on a full rebuild but I would like to sort it out a bit. The transmission is my main concern. If anyone has any ideas on what might be the cause I would be grateful. I can explain what's happening in more detail if required.
      Thanks everyone,
      Kester
       



COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...