Quantcast
Jump to content

2004 Suzuki Vinson wont run

biggdave92

By biggdave92
in Suzuki ATV Forum

 Share

Recommended Posts

biggdave92 Newbie

biggdave92

Posted
Posted

I am working on a vinson for a friend and i cant figure it out. I am getting spark. Carb has been cleaned. I soaked it for about 3 hours, rinsed, blew out passages, and re assembled. The bowl gasket could stand to be replaced but i didnt have parts at the time. I did look good enough to make a good seal though. Also, the air filter is removed. I am waiting on a new one to come in. So, when i first got the 4wheeler from him, he said it wouldnt run. i charged the battery, put some fresh gas in it and cranked it up. Next day i put a little seafoam in the tank, removed the air filter, and it wont crank. i held my hand over the intake with my fingers split to create a little suction and it still wont do anything. i've sprayed starter fluid into the intake, wont bust off. i cleaned the carb, still wont start.

i'm thinking the motor is not getting gas. also, i should add that the petcock is in the "PRI" position. Reason being is that when i disconnected the gas lines from the tank the only position that gas would run out is in the "PRI" position. when it is in the "on" or "res" position no gas runs out of the tank. Also, when i re installed the carb i put the petcock in the PRI position for about 1 minute to let the bowl fill up and i then removed the drain screw in the bowl to see if the bowl had fuel in it. It did not. No gas drained out. I checked the lines, they are clear.

also, i'm used to carbs with main butterfly and a choke butterfly. this carb has a main butterfly and some type of thing that slides up and down. what is that? how does it work? is it temp controlled?

ideas? thanks for any help!

oxidized_black Grand Master

oxidized_black

Posted
Posted

did you try putting a small amount of gas directly in the cylinder? i know you said you sprayed starter fluid in the carb... it should have done something if there was enough spark. have you tried a new spark plug? are coils or stators known to go on these bikes do you know?

biggdave92 Newbie

biggdave92

Posted
  • Author
Posted

no, i havnt put any gas in the cylinder via the plug hole. also, i pulled the plug out and laid it near the plug hole and turned it over to check spark and it was sparking very well. i know jack about these machines.

what is that big thing that slides up and down inside the carb throat? some type of choke? i'm not talking about the throttle butterfly.

BuckBilly Veteran

BuckBilly

Posted
Posted

The fuel system on that is a pressurized system. Prime forces gas threw . Check the fuel lines. get a squirt bottle and shot a little gas in it (try it out of the prime mode) . When you do get it to run, take it out of the prime mode.

Mudflap64 Collaborator

Mudflap64

Posted
Posted

Just a suggestion. I had a similar problem with my 02'...No start, acted like it was flooding, had great spark...It really had me stumped. Just for sh**s and giggles I swapped in a brand new plug and it fired right up. Just because you see a spark on the plug while its out doesn't mean it's sparking across the electrode where it's most needed in the combustion chamber. Just sharing an experience. I had mine tore down pretty bad and it ended up being a simple thing. It's worth a shot.

oxidized_black Grand Master

oxidized_black

Posted
Posted
Just a suggestion. I had a similar problem with my 02'...No start, acted like it was flooding, had great spark...It really had me stumped. Just for sh**s and giggles I swapped in a brand new plug and it fired right up. Just because you see a spark on the plug while its out doesn't mean it's sparking across the electrode where it's most needed in the combustion chamber. Just sharing an experience. I had mine tore down pretty bad and it ended up being a simple thing. It's worth a shot.

absolutely worth a shot!!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • TomJulio
      TRX300 No spark
      By TomJulio
      My 1992 TRX00 recently stopped firing.  I understand this is a common problem. I have ordered an aftermarket CDI unit.    TJ
    • Baldwin007
      2003 Suzuki 500 vinson 4x4 Owners Manual
      By Baldwin007
      I was wondering if anyone out there has a digital copy of an Owners Manual for a 2003 Suzuki 500 Vinson 4x4? I have a service manual, but no Owners Manual. I would like to know how to correctly operate/engage various features.
      Thanks
    • Guest
      Kawasaki Bayou no spark
      By Guest
      Hey all, new to the forum! I just bought a 1998 Kawasaki bayou 300, 4x4 not running. Initially I found no spark. Ended up playing with the plug wire (made sure plug top and wiring was touching) and got spark yesterday and the quad fired up off ether. Come to work on it today and now no spark again. Before I got spark and now today if I touch the plug after cranking I get shocked, and it will spark after I release the starter button. I was jumping the quad with a freshly charged car battery that has 12v while cranking. Cleaned out the kill switch and ignition button. All looks good. Purchased new plugs. They're are a lot of wires cut/ disconnected. But shouldn't matter if I got spark without them connected... 
    • RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • Asand211
      1995 Kawasaki KLF220 electric starter not working
      By Asand211
      I've got a 1995 220 Bayou and the electric start does not work.  When I got it the machine was pretty rough but I was told it ran less than a year ago.  The key switch had been cut off and wires  twisted after the key was lost.  I bought a new ignition switch and repaired the wiring and it is working correctly.  It is in neutral and the neutral light is on when the key is turned on but I get nothing when pressing the start button.  I verified there is no voltage going to the starter from the solenoid.  The fuse in the solenoid is good.  Something I found that is odd is that I get positive voltage(12 volts) to the brown, black, and white wires that run into the solenoid when the key is on.  That doesn't make sense to me but I could be wrong.  I would appreciate any help I can get. Thank you in advance.  

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...