Quantcast
Jump to content

Recommended Posts

Posted

I bought an 07 yfz 450 Bill Balance edition last november. It runs great, and has some mods that i cant quite figure out. I am pretty sure it has a big bore kit and a stage two cam on it. The problem is that the coolant leaks out of a tube that comes from the bottom of the right side of the ?crank case? (motor). It wasnt bad at all when I got it, but now that I have ridden it more, it starts to leak immediately upon starting. Even when its cold, and will continue to leak bad enough to empty the reservior under the seat in a matter of minutes. Any help would be great!:aargh:

Posted

Are you sure it's not an impeller seal that has gone bad causing a leak in that area? Seems common on those. Check out this video:

[ame=http://www.youtube.com/watch?v=f6M8Wc6uQZ8]yfz 450 coolant leak fix. Impeller seal replacement Part 1 of 2 - YouTube[/ame]

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By ButchM
      Hisun 700 EFI. Replaced TMAP sensor had broken off . Fuel pump pressure 41psi. The only way I can keep it running (and runs fine) is to close off fuel return line. 
    • By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 
    • By Sha35297
      I have this bike in my shop for a customer. It was sunk completely under water and left running until it killed. I did a complete engine rebuild. Replaced all bearings, crank, oil pump, and various other components. Engine starts and runs great. It will shift up through all gears perfectly in automatic and in ESP, but when slowing down it gets to 3rd gear and the MIL "-" light comes on and stays on. No flashes or anything and it will not shift gears. Kill the engine and restart in ESP mode and it is able to shift to neutral and start over. Does the same thing while down shifting in ESP mode. I replaced shift angle sensor with no improvement. Checked oil pressures as per repair manual "74psi" and higher with higher RPM's. With no MIL codes to point at an issue. I am at a loss as to what else to check or replace. Has anyone else ran across this issue?
    • By 97kingquad
      Okay so I bought this 1997 sazuki king quad from a guy and he had it for a few years. 
      He had it registered and on the trails last year but he said it bogged and backfired when he would try to drive it. so it sat for a year. 
      I bought it for 800 bucks and got it running that night and it ran great for a few days 
      But I parked it the other night and went to start it again and it was really hard to fire up and when I did it was bogging and idling high then low again.
      So I took the carb out and cleaned it (ended up doing it twice because it was still doing the same thing) 
      Now today I have it running slightly better, but it is still like 20% 
      I have been looking it up and trying to figure it out but I can't find the issue, has anyone else had this problem? I'll attach a video of it running and giving some throttle 
    • By TravisCr
      I don't know if I shouldn't have posted but I this is my second post on this (other was in regionals Forum)  The family has a 2-up 2004 Artic Cat and a 2003 Polaris Sportman and we are looking for fun/easy rides in the Colville, WA area- 70 Miles North of Spokane WA, we have a small trailer we can haul these with but need to find some good areas for beginner.

      Thanks in advance for any suggestions.
×
×
  • Create New...