Search the Community
Showing results for tags 'carburetor'.
-
Hello there I'm having a problem finding a quality carburetor for a 1993 Suzuki Quad Runner lt-f 250 2x4. I find a lot that have 3-4 star ratings. And all so far don't have the right throttle Cable inlet at the top. The last one I got 4 star on Amazon has a threaded cable sheath rest that could be partially drilled to work. I would prefer to get one I don't have to modify. Any recommendations are greatly appreciated!
-
Recently bought a yamaha beartracker and found that it was more powerfull than another beartracker i already owned so decided to swap carb from one i bought which was an original mikuni carb to other one which has a cheep chineese one in it but it did not like it at all and was bogging under load at full throttle ( leaning out) so just changed it back to original chineese one and it was happy again. Just tought it was strange that 2 identical bikes did not like each others carbs. It also was nothing to do with retricted fuel on one bike as there is plenty of flow on both bikes. Anybody any ideas?
-
Hello everyone ! I'm currently rebuilding my carburetor on my Yamaha moto 4 350 1987, first time I rebuild a carb 😅 ! It was leaking fuel from the overflow and inside the intake .... When I took off needle (the platic top part was stuck like crazy) I had a spring and inside the kit there is a spring, an O-Ring and a washer. Left is the needle that was in the carburetor and right is the new set (I already tried to mount it but it didn't felt right and I accidentally broke the o-ring) Anyway, I saw in some videos and diagram that there is no spring in here. So should I put the spring back ? And where ? On top of the needle or bottom ? This is an original Mikuni carb : Thank you ! Also if you have any additionnal tips please feel free to share I want to learn the proper way !
-
Hi I have a YAMAHA RAPTOR 660R 2003 I have taken of my Air filter and sprayed in my air inlet some carberator cleaner while starting it. That causes some problems. It struggles to start now. Please look at my attachedment video. What can I do now.? MOV_1402.mp4 MOV_1401.mp4
-
What is the best and easiest way to tune your carburetor? Any tips or tricks?
- 5 replies
-
- carburetor
- atv carburetor
-
(and 2 more)
Tagged with:
-
Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
-
Anyone have experience with after market carbs.
-
Bought a 01 bear tracker and a trailer from a local guy last week. I rebuilt the carb 2 days ago and ran damn near perfect for 2 hours. Parked it and came back the next day. It suddenly won't hold an idle at all and pops when I'm going downhill or at a slow speed. Almost like I'm dragging the whole power train with the weight of the ATV. It still has decent power (80-90% maybe as it is now) but I can't figure out why it's popping and won't hold an idle suddenly. even with messing with the idle screw next to the bowl on the exterior of the carb. No changes. . ANY ideas would be great. I'm far from a carb king, but I've never had this issue before. The fuel was bought 2 days ago and it has a brand new intake manifold as of yesterday when I rebuilt the carb (whole rebuild kit). I sprayed around the carb and did not find any leaks. Thanks y'all.
-
I have a Suzuki LT-Z250. My question is, can I replace my carburetor with one from a LT-Z400, if not, can you tell me why, if I can, do I need to make any modifications?
-
Looking for a carb for my 2003 honda trx300ex. any ideas?
- 6 replies
-
- carburetor
- honda
-
(and 1 more)
Tagged with: