-
Do you own an ATV, UTV or SxS? Join our Community Forum!
QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership.
-
-
Similar Forum Topics
-
By Clydaho
2022 Sector 550, 414 miles on it and the gas gauge reads empty. I topped off the gas and it didn't change.
There is no fuse that I could find. No access at the gauge cluster.
Wiring on the top of the tank looks good, properly connected.
Could the sending unit in the tank be stuck or broken?
Has anybody removed the tank lid? Any tricks?
Any other ideas?
Thanks for any help,
Clyde
-
By Drillbit
Hey all,
I need some input on a problem I'm having with my Kodiak 400 that keeps fouling plugs. First off, I've done a lot of work to this thing, most of it all in good fun. Brake work, cv joints, u joints, carb kit, checked valve lash, compression good, changed all fluids, etc... My problem is it keeps fouling plugs very quickly. I can put a new (manual recommended plug) in and it starts right up, runs great, idles great, picks up good. Doesn't stutter at all. I ride it for 1/2 a mile, it cuts off and won't start back up. I let it sit overnight thinking maybe it got to hot. Try to start it the next day, nothing. Put a new plug in, fires right up, runs great for another 1/2 mile or so, dead. The plugs come out and look carbon fouled with dry black soot on them. I don't know if this is a fuel/air mixture problem or a ignition problem. A couple of things that I noticed is I never need to pull the choke out to start it. Also, when it starts it automatically idles high like an automatic choke would do, then it comes back down to a good idle. Also I noticed that the air/fuel mixture needle valve screw does nothing when I adjust it in or out. I can screw it all the way closed and the motor still runs and idles good. Any advice would be greatly appreciated. I'm almost leaning to a ignition breaking down the plugs??
Thanks!
-
By Suzukiquad
I just bought two 2002 Suzuki LT80K. Do I need to mix the gas or use straight unleaded?
-
By Sofaspud
My 2008 can-am Outlander 800r is having hard shifting issues. Does anyone have a fix for this ?
-
By Am2007
Hi everyone,
Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so.
I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
owner manual
service manual
engine manual
I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it. im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
Thanks
-
-
Similar Tagged Forum Content
-
- 1 reply
- 5,077 views
-
- 16 replies
- 4,626 views
-
- 4 replies
- 7,832 views
-
- 2 replies
- 5,051 views
-
- 0 replies
- 4,158 views
-
-
Recently Browsing 0 members
- No registered users viewing this page.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.