Quantcast
Jump to content

2007 Arctic Cat 700 EFI massive headache

surbike11

By surbike11
in Arctic Cat ATV Forum

 Share

Recommended Posts

surbike11 Rookie

surbike11

Posted
Posted

Here is the story. I bought the atv used it one week at the hunting camp no issues. I go back the next week and its working great, I cut it off for a break and go to crank it and it has no spark. I tore the bike completely down(all plastics off). All wiring looked good. I started cheap new plug coil. still no spark. Oh by the way no codes came up either. Next was a ecm because everything was testing out good (stator etc). I put the ecm on and boom it busted right off and was running great. New issue I noticed the wires from the stator going to the rectifier were scorching hot I mean burn you hot. I shut it down and started to research. I checked all grounds again. All grounds were good so I ordered a rectifier. Put the new rectifier on and same thing super hot. So I ordered a new stator and pulsar. Keep in mind the scooter was running great just wires getting to hot. The stator according to all the specs tested out good but I couldn't figure what else to do. So I put the new stator on today and I am back to NO spark. Someone please help I am loosing my mind. Thanks

  • 3 weeks later...
skidooer_3 Contributor

skidooer_3

Posted
Posted

You may need a new wiring harness. Seems like you have two wires in the harness shorted and they may come and go, depending on if the wires are tight or loose. I have seen wires burnt off inside the insulated plastic coating before.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • TomJulio
      TRX300 No spark
      By TomJulio
      My 1992 TRX00 recently stopped firing.  I understand this is a common problem. I have ordered an aftermarket CDI unit.    TJ
    • HeWasRidinDirty
      2004 DVX 400 fuel issues
      By HeWasRidinDirty
      I rebuilt the carb on said machine. When I hook up the auxiliary gas tank it runs fine and everything is cool. When I put the fuel tank on and hooked up the lines, it completely flooded the cylinder and even about an inch of fuel in the air box. I'm pretty sure that it comes from the little hose on the petcock and hooks to the top of the carb. WTH is that even for? I mean the thing runs fine on the auxiliary tank, so idk And on the petcock when it's in the "on" position, I get no fuel. The petcock from the bike I took it apart and checked out how it operates. The sharpie marks indicate how it really works. Now the other petcock w/o the sharpie marks is an old one that was leaking that I removed from a Polaris quad. It's exactly the same thing, except the small hose and nipple have been removed. I'm so confused, LOL
       

       
    • jeffrocdx
      2002 Polaris 400 Sportsman Shift Indicator Issues
      By jeffrocdx
      I'm working on a 2002 Polaris Sportsman 400 with shift indicator problems. The indicator panel only will show Neutral and Reverse. If it's in High or Low, the indicator will show "R".
      I have replaced the three position indicator switch on the transmission. There is also a two position switch on the tranny that I didn't replace. If anyone is familiar with this problem, please let me know what I need to do. Any help is greatly appreciated!
    • cruteg8
      Is Crank Case swap possible?
      By cruteg8
      Does anyone know forsure if u can swap out the Crank Case on a 2001 kawasaki Lakota 300 sport  with a kawasaki Bayou 300 Im seeing yes and no all over some say the mounting position is different so you can't swap the cases but everyother inernal engine part you can swap then im seeing no problem bolts right on can someone plz clarify who knows forsure 
    • cruteg8
      Repairing Plastics
      By cruteg8
      I was thinking about trying to repair some cracks in the plastics of a Lakota Sport i just purchased has anyone ever tried (U.S. Chemical & Plastics USC GarageTM Flexible Glaze USC-77704 it) https://www.ebay.com/itm/364866165725. i was thinking jb weld for plastic then using this as a bondo that can be sanded smooth 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...