Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Todd Trask

Kawasaki Lakota 300 No Fire

Recommended Posts

Hello All, Finally got around to messing with quad. I found bad grounds & faulty coil. Ordered new today. Stole coil from other quad and made spark......woohooo....👍🏻. Well I temp installed new coil and made spark. Figured I would pour little gas in carb to see if it fires. No fire ..tried a little starting fluid just to see if it would fire. No fire.. well if I have spark, add clean fuel but No fire or booms from quad what’s so ever. Any suggestions..

Share this post


Link to post
Share on other sites


Yes you should have at least a little bit of a fire if you have spark. Is it possable that your  temp connections are good ? I would def take the carb apart and clean it just to get that out of the way. As far as spark goes is the plug fresh? If not put a new one in. 

Share this post


Link to post
Share on other sites

Topic moved to Kawasaki ATV forum and added issue to topic title. 😀

Share this post


Link to post
Share on other sites

I'm having the same problem. Checked the spark already. Turns over just fine, but no start.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Frank Angerano
      So i took a road trip today to look at a Suzuki Eiger! 2006 in perfect condition other then the fact it starts for 30 seconds and shuts down.  
      Its been sitting for about a year in a shed. 
      It has a plow and a winch included!!!
      Got it for a really good price and all looks good so far.  
       
      Stay tuned.  





    • By YamahaGrizzly
      Billy went all out and bought N2deep Snorkels, Rubber Down customs Rad kit and Rox speed fx Risers for his Grizzly 700. It took a solid 3 days in the shed to install all this new gear on Billys Yamaha grizzly 700! We cant wait for the next time we get out and go on a run! should be this week actually! gonna be good to get the Yamahas grizzlys and Kodiak together!
    • By mothrottle
      Does a US made grease gun fit Metric zerk fittings, or do I need a conversion to fit them?  Thanks in advance.
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By MarkinAR
      Have any of you fine folks used coil spring spacers to lift an ATV? Ole 93 Kodiak could use a smidge more lift and they are cheap enough. Might ride rough but that's ok cuz the shocks are toast anyway. 
      Thoughts?
  • Similar Tagged Content

    • By 87tecate4
      View File Lakota KEF-300 Service Manual 1995-2004
      Kawasaki Lakota 1994-2004 Service Manual
      Submitter 87tecate4 Submitted 07/10/2018 Category Kawasaki ATV  
    • By uzejo
      My lakota has a new carb and just had a top end redone by a professional, but it will not start. The electric start turns it over great, there seems to be compression. It seems like its trying to start, getting right there and just doesnt catch. It does start occasionally, but wont run for more than a couple of minutes and smells rich. Im assuming the carb needs to be tuned, but im just wondering if anyone else has any ideas before i get a chance to work on it.
       
      Thanks
    • By Brantley40
      What is the wheel bolt pattern for a 2002 Kawasaki Lakota Sport 300? Same on front and rear?
    • By Brantley40
      Anyone out there spice up their 2002 Kawasaki Lakota Sport 300 with cam, shaved head, deck the jug, valves?
      As you probably have already seen, I have a top end to get built back up and might as well add a little kick to it. Here's a pic of a golf cart I built up recently and modified the engine a little while I had it apart.
      Thanks in advance for everyone's help!!

    • By Todd Trask
      I have been online all night & this morning while taking care of my 2 yr old daughter with the flu.🤢.
      I am wondering why I cannot find a wiring diagram. I found in downloads , but it won't let me download..?????I only need one diagram not the whole manual. Rather spend money on accessories than $40 on a book for 1 pg. stator & pick up come Wednesday. So I'm going to bow hunt while weekend and ponder on wiring issues, with the intent to cure my quads illness. can anyone HELP..! 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...