Quantcast
Jump to content

Recommended Posts

  • 4 months later...
  • 1 month later...
Posted

My Niece has one of these Off Brand Sport Quads....I think it is 150 or 200cc's....WHAT A PIECE OF CRAP!!!!!!!!!!!!!!

I also know of More than 5 more Examples of the Same Style Quads but different Brand name that also have more Down time than Ride Time....Like I said in another post this morning.....The Smaller ones 49cc's are Working....The bigger ones are a waste of money....They also claim to be Honda Compatible....However,,,,Nothing Fits So Far...And Honda WILL NOT touch them..

  • 2 years later...
Posted
My Niece has one of these Off Brand Sport Quads....I think it is 150 or 200cc's....WHAT A PIECE OF CRAP!!!!!!!!!!!!!!

I also know of More than 5 more Examples of the Same Style Quads but different Brand name that also have more Down time than Ride Time....Like I said in another post this morning.....The Smaller ones 49cc's are Working....The bigger ones are a waste of money....They also claim to be Honda Compatible....However,,,,Nothing Fits So Far...And Honda WILL NOT touch them..

Agreed with everything u said... if u look at all of them its like they pull pieces off other brand atvs and glue it onto a frame

Posted

The ones on this website I have heard that they are nothing but junk. I have a friend that sells CFMOTO brand atv's. These are pretty good quality atv's. They have a very strong powerblock and the plastic actually survives a trip into the brush.

  • 4 weeks later...
Posted

I had a 50 extreme and it was a piece of crap. The jets got clogged at the riding park and i had to completly tear it down to get to the carb. Also the air filter always got clogged because it was in the back by the rear tire. I was always have to jack with it to run right.

I would only by japan made not china made.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By WeeBee
      I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
    • By Maddman200
      Can anyone recommend a good quailty bottm end rebuild kit for a 09 grizzly 700. I need to replace crankshaft and bearing and do not want junk quality?
    • By motox88
      Anyone have bad experience with these clutch kits?  Looking to get one for an 80s quad that I have.
    • By DaveswMN
      Pulled my '86 Moto4 out of shed where it sat for 20 years. I knew it smoked. checked it over a little put in gas and it fired right up!! 
      Drove about 100 yards, ran about half throttle wouldn't idle.  Put on somenew parts, jug/piston and rings, carb and valve seals.
      'went together ok, tuned it over by hand about 6 revs whick went well. Hit the starter it fired for about 6 revs and quit. tried it again fired once and then th sound of something slipping like maybe chain slipping over spoket.
      Took cover off to watch cam sproket, hit starter again, heard same noise and the cam sproket was not turning but jumping a bit. Chain was still tight. You will probably tell me I need to split the lower case but hoping there mightbe something else.
      I don't fully understand the chain tightener, the plunger only moves about 1/4 inch, should it move much more than that when off the motor and compressing it by hand?
      Thanks for any thoughts.
×
×
  • Create New...