Quantcast
Jump to content

Recommended Posts

Posted (edited)

Ok so I bought the 05 brute force and after putting about 60miles on it I have some concerns.

The engine seems to run REALLY HOT, like almost burnning my legs through my jeans hot but no warning light comes on and it doesnt seem to "act" hot is this normal, does it have any saftey feature to prevent over heating or heat damage?

It also seems to have a slight miss, or hesitation? When you slightly crack the throttle open and hold it at a steady RPM to give it a slightly higher idle it will run smooth for a couple seconds then miss and sometimes backfires. It also seems to sometimes have a hesitation if you jump on the throttle, what could cause this?

Also a couple times when shifting from reverse to high it sounded like it got hung up in between and there was a slight squeal as if maybe the belt was slipping and there was also a slight burning plastic of rubber smell. The belt IS new and it doesnt feel as if it is slipping when accelerating and the belt light hasnt come on.

Anyone have any suggestions?

It does seem to run really well and HARD accept for the slight hesitation or cough and the occasional backfire, I ran it up to 69MPH with both me and a buddy of mine on it, combined weight of almost 500lbs

Edited by jmeier1981
Posted
Ok so I bought the 05 brute force and after putting about 60miles on it I have some concerns.

The engine seems to run REALLY HOT, like almost burnning my legs through my jeans hot but no warning light comes on and it doesnt seem to "act" hot is this normal, does it have any saftey feature to prevent over heating or heat damage?

It also seems to have a slight miss, or hesitation? When you slightly crack the throttle open and hold it at a steady RPM to give it a slightly higher idle it will run smooth for a couple seconds then miss and sometimes backfires. It also seems to sometimes have a hesitation if you jump on the throttle, what could cause this?

Also a couple times when shifting from reverse to high it sounded like it got hung up in between and there was a slight squeal as if maybe the belt was slipping and there was also a slight burning plastic of rubber smell. The belt IS new and it doesnt feel as if it is slipping when accelerating and the belt light hasnt come on.

Anyone have any suggestions?

It does seem to run really well and HARD accept for the slight hesitation or cough and the occasional backfire, I ran it up to 69MPH with both me and a buddy of mine on it, combined weight of almost 500lbs

Sounds like it is running lean, You will want to get it jetted properly ASAP.(it is carbed, right?) That would answer the questions about the hesitation in the throttle and that could also be what is causing the heat.

Posted

Lean??? Really? I thought it smelled like it was running rich. The previous owner says that it was all stock and never modded or adjusted, would it require different jets or is it something that can be fixed with a couple turns of a screw on the carb?

Posted
And why do all of my post get renamed

Threads and posts are renamed by our moderators to be more search relevent and as descriptive as possible. For instance I just added the full year and manufacturer name. We do this in the branded forums to help get people to the threads they are looking for.

Since your quad is stock, I would shy away from any jet kits. Have you inspected your spark plug(s)? Try replacing that first.

Posted
And why do all of my post get renamed

I just noticed that in the branded forums, the announcement was not highlighted.

It states:

Announcement: Please include ATV year, make, model, cc, and technical issue (if you have one)...in your title when posting.

This is why our moderators may adjust a thread title to that format, if found not to be as descriptive as possible. Is this what you meant?

  • 15 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Rockbottom
      Replaced stator now red reverse light stays on in all forward gears and when neutral light in on 
      When put in reverse the light goes out
      any ideas how to correct
      thanks ahead
       
       
    • By digrig
      Hey everyone,
      I’m having an issue with my 2021 Polaris Sportsman 570 – the engine keeps stalling after running for about 10–15 minutes. I’ve checked the air filter, spark plug, and fuel lines, but can’t seem to find the root of the problem. It starts up just fine, but then loses power suddenly.
      Has anyone experienced a similar issue with this model/year? Would appreciate any advice or troubleshooting tips you’ve tried that worked. Thanks in advance for your help!
    • By T37Mark
      HI everyone. New to this forum. I have 98 Kawasaki Bayou 400 with an apparent electrical issue. I have the Clymer manual, but I am not exactly sure where to start. The issue started a month ago and the neutral light would go on and off intermittently. Eventually it went completely off , and I thought it was a shifting issue. I took the case off and checked the clutch and all mechanical shifting components are good, so I think I eliminated that. The switch sometimes works, sometimes doesn't. Last time I tried, I did hear a clicking sound near where the battery is right before the light went out. Does anyone have any ideas where to start? Hoping this is an easy fix.
    • By joezee13
      After turning off engine in neutral  starter wont engage If I rock unit back and forth it engages Getting progressive worse.
    • By middlebrookgt
      Hi All.  I introduced myself some weeks ago with my 2006 LT-F400F that needed a list of repairs including replacing the cracked generator cover.  It is back together as of last night and cranks up, idles and revs high pretty well.  Needs some fine tuning and stop backfiring at stop.
      The big issue is it will not go into gear.  I reassembled the insides with help from y’all’s posts.  The transfer selector moves from H-L-R, and the foot shifter moves thru the gears and finds neutral easily enough.  Before I tear it back open, the  transfer selector on top does not move as far as the repair manual says.  The diagram shows the shaft moving something like 40 degrees between L and H and 50+ degrees between L and R but it doesn’t move that far even though it finds the indent areas and moves well.  
      Could this be the problem.  I aligned all the dots on the shifter gears inside and it appeared to not be binding anywhere.  I do hear the gears touching when I shift like they are trying to engage, but zero movement from the ARV
      It was somewhat difficult to tell whether all the parts are installed on each shaft.
      Are there better/bigger photos somewhere that would allow me to be confident I included all the washers and bushings, etc?  If I had any doubt on parts that were laying inside after the cover broke then I purchased replacements from online stores.
      TIA for any input or feedback!!  Pics are from when I first took the generator cover off.


×
×
  • Create New...