Quantcast
Jump to content

2007 Arctic Cat 500 - Jumps In Gear When Starting Off

ScottBarry28

By ScottBarry28
in Arctic Cat ATV Forum

 Share

Recommended Posts

ScottBarry28 Rookie

ScottBarry28

Posted
Posted

My 2007 Arctic Cat 500 is acting up. I hope its just needing a new belt, but has anyone seen this before. Jumps when starting rolling in all gears. Once gets going its fine as long as you stay on gas. It feels like starting off in a rzr (takes a second to engage)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Forum Topics

    • noticon75
      Anyone ride in Kansas
      By noticon75
      Anyone ride at in the north east Kansas area? Tuttle Creek, Milford lake areas, Topeka?
    • tepin
      Багги Arctic Cat 700 инжектор 2008г пропала искра
      By tepin
      Здравствуйте, нужна помощь по ремонту багги Arctic Cat 700 EFI, пропала искра, датчик коленвала импульс есть, Самодиагностика показывает две ошибки AC99,AC96. все провода проверил на целостность, все датчики блоком определяются, не включается топливный насос. Провода от ECU до реле насоса и от реле до насоса исправны. Поставил подменный ECU, ничего не изменилось.   

    • Maxg_57
      Anyone there?
      By Maxg_57
      Is anyone still active on this club
    • Shorty51
      2006 Arctic Cat Utility transmission drive shaft replacement.
      By Shorty51
      Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
    • Jdeaton011989
      Timberwolf 250 starting issue
      By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...