Quantcast
Jump to content

Recommended Posts

Posted

I was plowing with my my quad last night and the thing just started sputtering and died. It will start and idle but if I put it in gear or try to give it gas while in neutral it stalls.

If I feather the gas it will rev but then winds down stalls and then pops.

I removed the carb and cleaned it, still doing it.

I drained the fuel and put new fuel with sea foam, still doing it.

I pulled the fuel line and started the engine and there is plenty of gas flowing out.

Maybe the electric choke? But I don't smell it flooding.

I guess I will try the plug next, but it doesn't seem like a plug issue, it's acting like a fuel thing. But the carb is super clean and the fuel is new.

Anyone have anything ideas?

Posted

That seems ok. I pulled the fuel line off of the carb and started it up. Running off of the fuel in the carb I half filled a water bottle before it stalled.

Carb boot looks ok.

I'll check the battery and see what the charging voltage is and report back.

Posted
If your plowing fluffy snow, the intake may have sucked in some snow. I would also check the intake for snow obstructions, the tires can sometime sling snow to the underside and that is where the intake is.

Mike

Everything was pretty caked with snow, but I can't see any evidence of moisture in the intake or aircleaner.

I think I may have fixed it today. I think it was a fouled plug.

I checked the battery (13.3 volts) and its charging at 14.5. So that seemed good. I pulled the plug out and it was wet so I know it's getting gas but it was also black and sooty.

After I replaced the plug I ran it around pretty hard through the snow for 20 minutes or so and it seems ok, no stalling.

I guess if the new plug fouls before the end of winter ill have to check if its running to rich and why it's running rich. It is doing a little back fire when I shut it off but I think it has always done that......

Thanks for all the feedback. Sharing info is better than shelling out 90 bucks an hour at the dealer any day.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • By Mister907
      Hi guys, I have a 2004 big bear 400. Last winter while plowing the driveway, I heard a loud pop from the left side of the engine. It continued to run as I looked for leaky fluid, but then died shortly after backing it up and won’t start now. The oil light comes on when I try to start it, no noise or anything else. 
      No blown fuses that I can find.
    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By Brent Wright
      What's a good size to start a 10 year old on?
×
×
  • Create New...