Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

May 2010 ATV Photo Contest!


Recommended Posts

May 2010 ATV Photo Contest

Theme: "Best Group Photo" with your ATVs, 3 wheelers, or UTVs."

* Does not have to be your machine(s), but you must have ownership to the photo, consent from the owner(s) of the machines to photograph them, and permission to use the photo on www.quadcrazy.com.

Prize: $25 Gift Certificate to Rocky Mountain ATV/MC & UTVOffroad Magazine (1 year subscription)

RMlogo.gif utvmag.gif

Rules: Submit your "Best Group Photo" with your ATVs, 3 wheelers, or UTVs." by entering it with a post, into this thread. (If you are not familiar with how to do this, visit the Learning Center) One photo per member allowed, so make sure it's a winner. You may submit photos that have not won past contests. Photos can be of yourself or taken by you. You may not submit photos that you do not have ownership of or permission to use. Any violation of these terms will result in disqualification.

NOTE: You MUST have a minimum post count of 10 to enter into the contest! We would like to see participation in our forums from all members who enter the contest.

Last day to enter a photo is May 27th.

Voting will take place for the last 4 days of May to determine the winner.

Voting will end May 31st and the winner will be announced!

Good Luck!

Link to comment
Share on other sites

This is a picture of one of our rides out in Carbondale, PA. The guy in the center of the picture int he green shirt, it was his birthday that day, 2 weeks later he was hit my a drunk driver while walking with his wife. RIP "Van Man" This pic also made it into dirt wheels in 2007.

Picture071.jpg

Link to comment
Share on other sites

It is deceptive as they were definatly up to Hooters standards with their jackets off. They had just pulled into the parking lot and I tried to convince my partners to wait until the weather got warmer before asking them to come over to take the pictures but they were a little over zealous. LOL

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Klacarta
      Buongiorno a tutti, ho un Raptor 660, e oggi alla prima accensione, il quad resta accelerato. Sapreste dirmi quale potrebbe essere la causa?
      grazie a tutti in anticipo....
    • By Ankromsathome
      Purchased a 2008 Yamaha Raptor 250 for my son about 1 year ago and have been having problems with the starting system ever since.
      Since owning for one year we have gone thru 2 starters and 2 starter gears. Now its spring 2019 and time for a third replacement. Am starting to think that we may have a more serious issue.
      Upon replacing, the starter and starter gear, its starts fine, then after about 10 starts, you start to hear a bit of grinding. The grinding slowly gets worse until the teeth on the starter and the starter gear become trashed.
      I've heard possible solutions from the starter clutch needing replaced to the casing for the starter gear shaft being out of spec?
      I've also noticed that here is no difference or change if its in gear or not.
      I just replaced the trans clutch as well.
      Any suggestions?
       
    • By Yamess350
      so I bought this raptor from my bubby because it sat in his garage for a year or suck long story short the guy who lost worked on it didn't know what he was doing can just did some of the worst work I've ever laid my eyes on but I recently had the thing running and delt with a lot of problems getting the damn thing to spark need new stator/ cdi and wiring harness and I had finally got the thing to run and drive had a blast omg I love this thing but sometimes I pray it would just stop giving me problems I've road the quad 2-3 time and found there was a huge leak and I took the head off its new btw its black and shiny but the last guy who worked on it did a horrible job and lost parts any ways I fix his mistake and bought oem parts and gaskets but when I when to put the piston back in I could not find a good thread on the orientation on all the rings on the piston and it is a bit confusing how people describe each ring I need a layman's terms like talk to me like I'm slow lol but don't be rude and I need help 1 in the orientation on all the rings and also my engine stopped sucking threw the carb can it be the valve is not seated on intake/exhaust should I reopen the head and redo the rings on the piston or can it be the valve spring gap idk I need help all I know right know is I need a break from the bike and collect information for now can I get some help without people pointing me in all kinds of direction 
    • By Donaldhang92
      Hi, I am new to the forum I bought a 2006 raptor 350 I test drove it. It ran decent but thought it was just due to the cold, after I got at home I rode it around and it would just die out/ lose power upon letting off from heavy acceleration or down shifting, it will just lose power and die out, I took carburetor apart cleaned it pretty well, it ran a little better at first then 1 minute into test ride she died again. Now I’m back to my shop and try to start it again and I’m left with a crazy slapping clicking noise I’ve never heard before. Let me know if you have heard this or know of the answer to my problems thanks ! 
      IMG_7843.MOV    
    • By blakkmajikk74
      hello I have a 2004 Yamaha Raptor 600. it sat in storage for 2 years and I recently pulled it out to ride and it didn't start. I replaced almost every part on it, got it to start but a wire burnt out on it. i paid a few guys to help me fix it and its still not fixed. its been almost a year and i'm lost. This is how they left my bike, and i'm willing to fix it myself now because i have spent too much money paying to get it fixed!!!
       



       
      IMG_0226.HEIC IMG_0224.HEIC IMG_0221.HEIC
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...