Quantcast
Jump to content


2000 Suzuki LTF 250 runs poor after warming up


bauerj64

Recommended Posts

We have a 2000 Suzuki LTF 250 that we are having an issue with and a re looking to you members for ideas/help. This machine starts and runs great but after awhile when it gets hot (not overheated) but after 10 minutes or so it starts to bog down, loose power, miss etc. If I slow down too much it will stall and not restart until after it cools off again. This problem started happening AFTER we replaced the entire carburetor for a totally unrelated issue, so prior to that, it ran perfect. Any thoughts or ideas are welcomed. Thanks in advance.

Jeff

Link to comment
Share on other sites

Sounds like you have a bad CDI. They aren't cheap, so I would test all the other ignition components first. If you don't have a repair manual, buy one, there will be simple tests in there to check the coil and such. It will also have a troubleshooting guide that you may find helpful. Also, check your wiring for loose connections and bad grounds. It also wouldn't hurt to pull the plug the next time the machine dies on you, ground it against the motor and check for spark, just to comfirm that the problem is in the ignition.

Link to comment
Share on other sites

  • 3 months later...

my ltf250 4x4 had the same problem. i replaced the plug and adjusted the carb because it had a fouled plug when i pulled it out. try a new plug and maybe a fuel pump because my fuel pump went bad and it did the same thing, like there was a vaccum leak. and there also may be air in the fuel line and pump

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
×
×
  • Create New...