Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

This should be fun. It's pretty clean. Doesn't start but by tomorrow night I'll have it going. 500 bucks. 2a929dce3bc28830ef905ea97a41a876.jpg

 

Sent from my SM-N920V using Tapatalk

 

 

Share this post


Link to post
Share on other sites


I'm thinking starter relay. But I'll pull it apart and inspect everything.

Sent from my SM-N920V using Tapatalk

Yup6600e57b66e7d638cfed88df5bcfb78f.jpg

Sent from my SM-N920V using Tapatalk

  • Like 1

Share this post


Link to post
Share on other sites

They tend to get water inside, rust and they get stuck,they all come with cheap parts,could be the rear brake switch also,

  • Like 1

Share this post


Link to post
Share on other sites

It just clicks when you press the start button. I will pull the sp tomorrow and inspect the walls and head.

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites


It just clicks when you press the start button. I will pull the sp tomorrow and inspect the walls and head.

Sent from my SM-N920V using Tapatalk


Switch assembly go bad too,but you already know that I bet....check compression and all those goodies....

Sent from my SM-N950U1 using Tapatalk

  • Like 1

Share this post


Link to post
Share on other sites

Nice little project bike.   Can’t wait to see what you find and how it goes.  

Share this post


Link to post
Share on other sites

Okay. All clean inside from view of the sp. I put 2 stroke oil in it cause it will burn off anyway. I took a straw and stuck it in the qt container. Sealed the straw. Then blew into the sp hole. Let it sit and cranked over. I figured I would crank the hell out of it to lube the cylinder. But by the time that was said and done. The battery is dead. I did notice a few loose wires that I tightened

Sent from my SM-N920V using Tapatalk

  • Like 1

Share this post


Link to post
Share on other sites

I have to sort things out. And my kids helping so who knows how long. Lol

Sent from my SM-N920V using Tapatalk

  • Like 2

Share this post


Link to post
Share on other sites


I have to sort things out. And my kids helping so who knows how long. Lol

Sent from my SM-N920V using Tapatalk


I have my son too but all he does is takes my tools and parts places them everywhere,(only 2 years old boy twin) but he loves atv's just as I did when I was a kid.... good stuff bro... I saw an atv like the one you got for 600 (2017) dont know what's wrong with it, didn't get in to it,to many projects on my hands now

Sent from my SM-N950U1 using Tapatalk

Share this post


Link to post
Share on other sites

Fried coil. Cracked stator case. No. Not cracked. Has a good size hole.

Sent from my SM-N920V using Tapatalk

  • Sad 1

Share this post


Link to post
Share on other sites
5 hours ago, 06kfx440 said:

Fried coil. Cracked stator case. No. Not cracked. Has a good size hole.

Sent from my SM-N920V using Tapatalk
 

That sucks. Can you find parts for it? Is that a chinese ATV?

Share this post


Link to post
Share on other sites


I can find parts. I'm just going to replace a bunch of things. Even if it doesn't need to be changed.

Sent from my SM-N920V using Tapatalk

Yeah. They are all pretty much the same for all of them

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites

If the cover has a hole and you can’t find a replacement  there are always people out there that can close it up with a little heliarc welding job. Prob cost you $25 but worth it. 

 

  • Like 1

Share this post


Link to post
Share on other sites

It's like a plastic cover. Or a very thin metal. I ordered that along with 5 other things. Cost 35 bucks

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites

Thanks bro. I'll take pics when I get back out there

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites


Just a thought. What would make it so the starter doesn't turn when you put power directly to the starter?

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites

What if it's new

Sent from my SM-N920V using Tapatalk

Share this post


Link to post
Share on other sites

Is the starter mounted on the bike ? If so then maybe it’s locked up some how. 

Are you seeing a slight spark when you apply direct voltage ? And also can you remover the starter if it’s installed.  

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By uzejo
      My lakota has a new carb and just had a top end redone by a professional, but it will not start. The electric start turns it over great, there seems to be compression. It seems like its trying to start, getting right there and just doesnt catch. It does start occasionally, but wont run for more than a couple of minutes and smells rich. Im assuming the carb needs to be tuned, but im just wondering if anyone else has any ideas before i get a chance to work on it.
       
      Thanks
    • By Ed Zeppeli
      Hi all,

      I picked up this quad after the previous owner couldn't get it going.

      The issue is that I can't get it to fire at idle or at all.

      I've...

      - replaced plug. Decent blue spark. Also tested with spark tester inline.
      - rebuilt the carb. PO had already bypassed vacuum lines from petcock. There's fuel at the cylinder
      - Checked compression with new gauge. reads 190 psi
      - cleaned all contacts I could access.
      - am currently jumping with car battery. Solenoid jumpered.
      - checked cam timing at TDC and adjusted valve lash
      - put gas directly into cylinder to see if it will fire at least momentarily

      Motor turns over well. Plug gets wet. 

      Motor may fire once or twice but smokes through exhaust a bit as if it's trying to fire or combusting.

      This leads me to suspect timing. As mentioned I checked the flywheel mark versus cam marks. Perhaps someone has been in there before because I can't find a 'T' on the flywheel but there is a very visible paint mark which aligns with TDC position on piston. Possibly a slipped flywheel/woodruff?

      Is it possible that if it had seen previous repairs, that the timing could still be off? I'm reluctant to dig into the flywheel/stator area if there's something else I could have missed but all signs point me to that area. Would a bad CDI cause spark timing to be off?

      Anywhere else to diagnose incorrect spark timing?


      I've scoured these forums and elsewhere but I'm posting just in case there's something I've overlooked up until now.

      Thanks very much for reading!


      Warren
    • By Chad Dickerson
      I am goin nuts here! I have a 04 400 air cooled 4x4 , I'm a atv,car,truck,mower mechanic for yrs,just sayin. Ok it cranks and kinda fires now and again then after 5 min of cranking and stopping itl start if u touch throttle itl did then u start all over! If u let it warm up sumtimes u can throttle it up other times it just does! Just depends on it? When it stays running it runs awesome,no problems except it just does randomly like u shut key off? Sumtimes itl start right back up others itl do the no start thing! IV put new plug,adjusted valves and hot tanked carb? I'm at a loss here guys! Please any other ideas? I don't think it's anything to do with flywheel? It's not the auto it has a hi low reverse lever on left fender and foot shifter? Help please lol
    • By JacobSlabach
      i know this isnt an atv but same type of thing.  I have a riding mower im fixing and selling for my aunt and it has a dead battery.  i jumped it off my atv and when i turn the key nothing at all happens.  i tried jumping the relay still nothing.  this is with the seat down.  you wouldnt think this mower would have issues as its a top-of-the-line brand and almost brand new (aunt found it for a good price, still got tits on tires, just sat for a couple months in a mechanic shop
    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...