Quantcast
Jump to content

Recommended Posts

Posted

My friend has a '04 400 eiger 4x4. he took it through the mud and it died. ever since it doesnt run very good and it smokes really bad. we drained all the fluids and filled them again. we did that a couple times cause it was still smokin. my thoughts are the piston wall is gouged out but i dont know. any ideas? also where can i find a good diagram of the motor in case we have to tear it down?

Posted

Do a compression test. That will tell you alot. Did you check your air filter? It could have just gotten really dirty. If you need to get into the motor, get a manual, it will have diagrams and specs that you need.

  • 5 weeks later...
Posted

Hello.

Was there much oil in the motor when you drained it out the first time?

Many Eigers when they are ran out of oil, scuff up the piston and alloy melts off the piston on to the cylinder wall, then killing the rings.

Then when you put more oil in to the oil rings dont work and the bike blows alot of smoke.

But normaly still runns ok for most people.

you did say that it was a muddy ride, so there is a chance that the oil cooler is covered in dryed mud and stopped air flow and thus the guy over heated the motor, and killed the piston/rings.

Did he get bogged and reved it like mad to get out and keept trying?

  • 1 month later...
Posted

i just bought a used 03 eiger with no compression it had been run out of oil and the oil cooler fan fuse was blown make sure the fan works!!! or you will melt the piston you might get off cheap replacing the rings but rings and a piston are about 150 bucks

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By docdoug72
      Has anyone had a suzuki 230 quad lock the engine up?  Its a well maintained bike, it locked up when my son was riding it. Pulled the plug, it has connected with the piston. I'm thinking the con rod let go.  I don't have a service manual.  Does the engine need to come out to check further?
    • By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • By RadRob
      I am new to this site. I have a 1987 Suzuki LT230S Quadsport I think. Is there a difference between quadsport and quadrunner?
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
×
×
  • Create New...