Quantcast
Jump to content


carb question


frizzen

Recommended Posts

Your bike will run a bit richer at that altitude, if it is jetted properly for 4000 feet, then you should be able to get away without re-jetting. Besides, it will likely be colder up there, so that will help offset richening effect of the higher altitude. If you are jetted for sea level, then you may start to see problems at 8500. If you choose not to re-jet, make sure you carry a spare plug in case you foul yours. Also, something to clean a plug with, you can clean and re-use a wet fouled plug. If you have poor performance issues, you can just open up your airbox, just make sure not to let any water get in there when it is opened up. It is pretty easy to change a main, jet even on the trail, you could just bring some extra jets with you and change to a bigger one if you need to. Also, make sure you have a screwdriver to make adjustments to your pilot screw, you will probably need to do that too.

Link to comment
Share on other sites

How much difference does it make if you go to a different altitude? I live at about 4000 feet and plan to go do some riding at 8500. Is it worth the trouble to change the jet in the carb if I am just going to do some forest trail riding? I am on a 2003 arctic cat 500.

you should be fine !You might feel a slight loss of power but not enough to matter I ride at 8500' and above and my quad is jetted for 5000'

Link to comment
Share on other sites

the best way to be safe with your engine in mind is to pull a plug when you are at that altitude after riding a bit and check you plug. do a wot test if you need to be sure. also it usually is the opposite when you ride in the mountains or higher terrain. it is ussually warmer the higher you go. the only difference is less burnable oxygen. it can be harder on your machine if it is to rich.

Link to comment
Share on other sites

the best way to be safe with your engine in mind is to pull a plug when you are at that altitude after riding a bit and check you plug. do a wot test if you need to be sure. also it usually is the opposite when you ride in the mountains or higher terrain. it is ussually warmer the higher you go. the only difference is less burnable oxygen. it can be harder on your machine if it is to rich.

It is a fact that the average temperature goes down as you go up in elevation. That is why it snows in the mountains while it is raining in lowlands at the bottom of the mountains. The average temperature drop when going from 5000ft to 8000ft is about 10 degrees. This will mean more dissolved oxygen in the air, which will help offset the affect of the less dense air at the higher altitude. Your motor will still run richer at a higher altitude, but in the winter, when it is alot colder in the mountains, it isn't as bad because of the significantly cooler temps.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By Suzukiquad
      I have a 97 Yamaha Timberwolf and it is beyond loud, is there any good options to silence them or at least make them bare able to drive. I know it has a crack in the exhaust pipe, but even with that fixed its still loud. 
    • By 1998Zuki250
      What are your riding location preferences? Mud Park? Personal Trails? Public Land?
    • By jashadams
      Hey all back again with my 1989 moto 4 250.
      After putting a new carb on it it's really sputtery, it has new gas and I'm wondering what to tune on the carb to make it idle better. I've attached a video to describe the issue more. The bike is still work in progress but I think the video gets the point across. Thanks!
      Snapchat-1142015191.mp4
×
×
  • Create New...