Quantcast
Jump to content

Recommended Posts

Posted

Hey guys hope everyone is well. I need sum advice or help. Anyways I already rebuilt the carb however I noticed that the carb is spitting sum gas towards the airbox and i did a compression test and i only got 50lbs what should the compression be for these lil monsters bc 50 lbs isn't a lot I figure it will b around 100lb or so. So I'm thinkn a piston,bad valves? it does smoke white but I can get it to run but hard to start and I got to keep the slide all the way open on the carb to get it to even run but once I let the slide down it cuts off so its not even driveable right now plz help me guys trying to get it running b4 we get snow

Posted

Thanks ox I knew it was to low. so what u think bad piston rings or bad valve? It is spitting a lil gas out towards airbox, so I'm guessing air is sumhow getting out and pushing sum gas out of carb.

Posted

valves and timing can also be the prob... i would check and see how tight the valves are adjusted ... if you have a service manual on it ...it will tell you how to do this ... and you can also check the timing that way ... it almost sounds like the timing chain might have jumped 1 tooth ..

Posted

Thanks guys unfortunately I dnt have a book so I dnt know how to check timing and valves I'm pretty much doin this with out a book and mainly guess wrk. It does have around 5k miles on her and the recent owner didn't maintain it very well. Any tips on how to check that stuff. If I have to break it down anyone know where I can get a good performance cam for it and get it bored to next size hopefully that will give me sum extra power

Posted

So today I set my valves however still a no go. I set intake at .004 and exhaust at .006 now I'm geting backfire thru the carb and cnt get it to start at all also put a new plug in. Any other ideas guys? And yes it was on tdc

Posted

So I set my valves again and it cranked up first time it ran about 2 mins then cut off I got valves set int .004 exhaust .005 I put it on tdc by taking plug out and feeling for air then use the hand starter to put piston on top I got needle jet about 2.5 turns out should I turn it in some so I can get it to idle. And got new spark plug gapped at .26 any tips guys or ideas what I should do or check

Posted

What's up ox. Naw I dnt know y it shut off. When I reset the valves she cranked as soon as I turned it over. I do have my air mix screw turned all the way in til I can get it to idle and get it set however when it did crank it didn't idle high with the air mixture all the way in which it shud have. I'm thinking its fuel problem bc when I took old plug out it was extremely black and had residue on it as well so burning rich right?. I got the needle jet set at 2.5 turns out frm seated. It's almost bck to same problem it will crank if I raise the slider half way up to give it more air

Posted

I just thought about sumthn the needle that goes in the slide which way does it go in? Do the grooves and clip need to b up or down? I think this is my problem its to cold and dark to mess with it right now so I'm gonna try it tomm

Posted

I got it to idle and kinda wnts to bog when I give it gas then after playing with it a while I can give it gas however when I give it full throttle for about a min she will cut off and I noticed the float bowl is completely dry! Any ideas ? Bad float or bad float spacing or sumthn

Posted

Checked compression its at 95psi now so better then b4. bout to check timing shortly gotta figure out how to check that I got plastic off I kno how to line cam gear but not crankshaft part I'm sure its simple

  • 2 weeks later...
Posted (edited)

Could be bad fuel lines or fuel filter/pump. Pilot screw setting might be closed too. And your going to want the valves a 6 thousandths and maybe even 7 thousandths for the exhaust valve because it will expand a little with the heat.

And make sure you run premium fuel in there because anything else is terrible on the carbs

Edited by Thayer40
  • 2 weeks later...
  • 2 weeks later...
Posted

I hvnt had much time but i did put a new float in it. Still bog when I give it full throttle but Idles good my book said pilot needs to be 2.5 out but il try 3 and readjust valves again il let u kno what happens when I get a chance to mess with it

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Mikey69
      Heres my story. Kinda long. I guess I was a late bloomer when it comes to quads. I had never ridden a quad in my life. Rode Dirt Bikes as a kid growing up. Back in Oct of '06 I found a Mustang on craigslist. Took it for a test drive one morning before work. Fast car. 351 Cleveland. I had planned on meeting the guy again after work. For some strange reason thats still to this day beyond me, I stopped in Hillsboro MotoSports on the way home from work. I had 6 Grand on me. There was a left over '05 sitting by the front door. It was on sale for $4999. It was $5499 OTD. I didnt even look at anything else. I knew nothing about quads accept I thought it really looked coool and I had the money in my pocket to buy it. I was sitting on it when the salesman walked up and asked... "Can I help you?" Without hestitation I pulled 60 Ben Franklins outta my front pocket and said "I want this Quad. Load it up in my truck." It was just about dark by the time I drove away from the shop. BTW, I didnt bother to ask my ol lady if I could buy it. LOL. Anyway, I took it by the house and showed her. She was kinda stunned but not mad. We drove over to a friend of mines house and unloaded it. I took it to the field across the street from his house. HOLY CHIT!!!!! I was surprised by the power. I had it for about 2 weeks and took it to Sand Lake. I was there a few hours and rolled it on a banked turn at the top of the bowl right before you get to the one-ways. When it rolled, I flew off and landed on my belly. The quad came bouncing and landed on my back. For a month I couldnt even walk. I was scared of it. I considered trading it for a 250EX. Went back to the shop. The salesman said..."Dude!!! You dont want a 250EX!!! Trust me. Just get used to it" I still wasnt convinced. I put it on craigslist for $4000. Calls were coming in. I had a guy that wanted to come look at it that evening. I decided to take it for one last ride at Browns Camp before I sold it. I was still afraid of it. After about 5 minutes I started feeling comfortable on it again. I decided right then, I loved my Honda 450 and would learn how to ride it instead of selling it. That was late Nov of '06. Work was slow for a Painter in Oregon. My new job everyday? Going to Browns Camp and ridding my Quad. I bought my Girl Friend an '02 Blaster. I rode my 450 for 4-6 hours almost every single day for 3 months. And yes, I know my way around Browns Camp pretty well. LOL. In March I bought her an '06 TRX250EX (Thank God I didnt trade my 450 for one of those) LOL Since then, I have become totally addicted to quads. I love them. Couldnt imagine not owning at least one quad. Luckily I have two. My "07 was $6500 OTD in July of '07. Bought it for my Girlfriend. Traded in her 250 EX. A month later we broke up. So, I wound up with two Honda 450's.
       
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By Trent Finnessey
      So I’ve got a 2000 Honda 400ex absolutely love it!! I’ve had it for about a month, I ride with bruteforce 750’s, outlander 850’s and 1000 sxs’s and I was thinking of getting a trx450r carb and a full hmf exhaust. And probably doing the air box mod too, how much power would this give my 400? Just a little different or a big difference? Cuz if it’s not much of a different I’ll just stick with my dg slip on..... thanks!
    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
×
×
  • Create New...