Quantcast
Jump to content


91 Suzuki Kingquad 300 low compression, wont start


bsfs1988

Recommended Posts

Hey guys hope everyone is well. I need sum advice or help. Anyways I already rebuilt the carb however I noticed that the carb is spitting sum gas towards the airbox and i did a compression test and i only got 50lbs what should the compression be for these lil monsters bc 50 lbs isn't a lot I figure it will b around 100lb or so. So I'm thinkn a piston,bad valves? it does smoke white but I can get it to run but hard to start and I got to keep the slide all the way open on the carb to get it to even run but once I let the slide down it cuts off so its not even driveable right now plz help me guys trying to get it running b4 we get snow

Link to comment
Share on other sites

Thanks guys unfortunately I dnt have a book so I dnt know how to check timing and valves I'm pretty much doin this with out a book and mainly guess wrk. It does have around 5k miles on her and the recent owner didn't maintain it very well. Any tips on how to check that stuff. If I have to break it down anyone know where I can get a good performance cam for it and get it bored to next size hopefully that will give me sum extra power

Link to comment
Share on other sites

So I set my valves again and it cranked up first time it ran about 2 mins then cut off I got valves set int .004 exhaust .005 I put it on tdc by taking plug out and feeling for air then use the hand starter to put piston on top I got needle jet about 2.5 turns out should I turn it in some so I can get it to idle. And got new spark plug gapped at .26 any tips guys or ideas what I should do or check

Link to comment
Share on other sites

What's up ox. Naw I dnt know y it shut off. When I reset the valves she cranked as soon as I turned it over. I do have my air mix screw turned all the way in til I can get it to idle and get it set however when it did crank it didn't idle high with the air mixture all the way in which it shud have. I'm thinking its fuel problem bc when I took old plug out it was extremely black and had residue on it as well so burning rich right?. I got the needle jet set at 2.5 turns out frm seated. It's almost bck to same problem it will crank if I raise the slider half way up to give it more air

Link to comment
Share on other sites

I got it to idle and kinda wnts to bog when I give it gas then after playing with it a while I can give it gas however when I give it full throttle for about a min she will cut off and I noticed the float bowl is completely dry! Any ideas ? Bad float or bad float spacing or sumthn

Link to comment
Share on other sites

  • 2 weeks later...

Could be bad fuel lines or fuel filter/pump. Pilot screw setting might be closed too. And your going to want the valves a 6 thousandths and maybe even 7 thousandths for the exhaust valve because it will expand a little with the heat.

And make sure you run premium fuel in there because anything else is terrible on the carbs

Edited by Thayer40
Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By lester
      I picked up a 2000 Big Bear 400 4X4 that was sitting around that I know nothing about. It will not start. I do have a red light when in reverse. When I take it out of reverse, I do not get a green neutral light, and when I push the start button the red oil light comes on but there are no noises, nothing else happens. How do I test the neutral switch and/or bypass it to see if I can get it to at least crank? And does anyone have other suggestions for me to try?
    • By Mikey69
      Heres my story. Kinda long. I guess I was a late bloomer when it comes to quads. I had never ridden a quad in my life. Rode Dirt Bikes as a kid growing up. Back in Oct of '06 I found a Mustang on craigslist. Took it for a test drive one morning before work. Fast car. 351 Cleveland. I had planned on meeting the guy again after work. For some strange reason thats still to this day beyond me, I stopped in Hillsboro MotoSports on the way home from work. I had 6 Grand on me. There was a left over '05 sitting by the front door. It was on sale for $4999. It was $5499 OTD. I didnt even look at anything else. I knew nothing about quads accept I thought it really looked coool and I had the money in my pocket to buy it. I was sitting on it when the salesman walked up and asked... "Can I help you?" Without hestitation I pulled 60 Ben Franklins outta my front pocket and said "I want this Quad. Load it up in my truck." It was just about dark by the time I drove away from the shop. BTW, I didnt bother to ask my ol lady if I could buy it. LOL. Anyway, I took it by the house and showed her. She was kinda stunned but not mad. We drove over to a friend of mines house and unloaded it. I took it to the field across the street from his house. HOLY CHIT!!!!! I was surprised by the power. I had it for about 2 weeks and took it to Sand Lake. I was there a few hours and rolled it on a banked turn at the top of the bowl right before you get to the one-ways. When it rolled, I flew off and landed on my belly. The quad came bouncing and landed on my back. For a month I couldnt even walk. I was scared of it. I considered trading it for a 250EX. Went back to the shop. The salesman said..."Dude!!! You dont want a 250EX!!! Trust me. Just get used to it" I still wasnt convinced. I put it on craigslist for $4000. Calls were coming in. I had a guy that wanted to come look at it that evening. I decided to take it for one last ride at Browns Camp before I sold it. I was still afraid of it. After about 5 minutes I started feeling comfortable on it again. I decided right then, I loved my Honda 450 and would learn how to ride it instead of selling it. That was late Nov of '06. Work was slow for a Painter in Oregon. My new job everyday? Going to Browns Camp and ridding my Quad. I bought my Girl Friend an '02 Blaster. I rode my 450 for 4-6 hours almost every single day for 3 months. And yes, I know my way around Browns Camp pretty well. LOL. In March I bought her an '06 TRX250EX (Thank God I didnt trade my 450 for one of those) LOL Since then, I have become totally addicted to quads. I love them. Couldnt imagine not owning at least one quad. Luckily I have two. My "07 was $6500 OTD in July of '07. Bought it for my Girlfriend. Traded in her 250 EX. A month later we broke up. So, I wound up with two Honda 450's.
       
    • By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • By BenJammin
      I did a compression test on my 2005 Bombardier Traxter 650 CVT and it's 75 PSI.  service manual only talks about leak down test.  No specification for engine compression the manual.  What does 75 PSI tell me?  Thank in advance.
       
      A little history of this machine.  640 miles.  Picked it up about 2 years ago, not running. Probably the computer.  Tested all circuits and confirm it was the computer.  Long story short, I watched a Youtube video and fixed the computer. ATV now started and runs.  BUT, it tops out 20 MPH.  I cleaned the carb 3 times also using a Mikuni carb kit after the second time.  Slide in carb is going up and down.  Only adjustment for fuel is at 1.5 turns out.  NGK Sparkplug had soot on main part but brown on the electrode.  Champion sparkplug is brown.  I check CVT clutches and they both appear to engage like they suppose to.  Checked valve clearance it's 0.00, I can't get any feeler gauges in-between.  I check timing chain I believe it's in the correct position and hasn't skipped.  I removed muffler plug and drilled into muffler to try and make sure it wasn't plugged.
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
×
×
  • Create New...