-
Popular Now
-
-
Similar Forum Topics
-
By mikeexplorer
I took this video back in 2007. Recently the trail (old railroad grade) I was riding was converted into a walking trail (obviously no more ATV riding on it) 👎 I dug up this old video and put it together since it shows the entire section and what it used to look like. The quality of the video is lacking, but this was from 18 years ago. Image stabilization didn't exist back then so I wore the camera on my helmet. (mounted to the quad was useless with all the shaking) so there is some annoying frames of me looking around. I noted any historical items from the railroad in the video. There is a section where the railroad grade is wiped out due to erosion so I had to jump off it and ride an abandoned road for a section to get around it.
-
By qcm413
Hi,
i need to replace my tire on my atv and i want to know if somebody have a good tire experience on mid-mud terrain and winter plowing. im not sure if i am to go with a tile like a tractor thread or the other ones like ITP mud lite
thank in advance
-
By DaveswMN
Pulled my '86 Moto4 out of shed where it sat for 20 years. I knew it smoked. checked it over a little put in gas and it fired right up!!
Drove about 100 yards, ran about half throttle wouldn't idle. Put on somenew parts, jug/piston and rings, carb and valve seals.
'went together ok, tuned it over by hand about 6 revs whick went well. Hit the starter it fired for about 6 revs and quit. tried it again fired once and then th sound of something slipping like maybe chain slipping over spoket.
Took cover off to watch cam sproket, hit starter again, heard same noise and the cam sproket was not turning but jumping a bit. Chain was still tight. You will probably tell me I need to split the lower case but hoping there mightbe something else.
I don't fully understand the chain tightener, the plunger only moves about 1/4 inch, should it move much more than that when off the motor and compressing it by hand?
Thanks for any thoughts.
-
By DayBreakJim
So my latest wheeler is a 04 Yamaha Bruin 350. It had all the wires cut from the stator and a few others and no wiring harnesses. The previous owner had them all twisted together and the bike neutral light would come on it would start (hard to start) but then would idle fine. It would die when you gave it gas so I soldered all the wires together and went on inspecting assuming it was a carb issue. Later after the carb was cleaned and adjusted I got this (see video). The bike would want to die anytime you gave it gas and there would be this horrible knocking sound but only when you gave it gas. I was worried it was the rod bearing and electrical still messed up somehow.
Upon further inspection of the wires coming from the stator there was a W/R wired to R and a R wired to W/R. I switched them so they matched per the service manual (W/R to W/R and R to R) and the bike started right up, idled and revved out fine and the knocking noise disappeared. This was the problem the whole time. It was just really hard to tell bc the oem wires coming from the stator were so brown and dirty I could barely make out which was which.
Where the hell did that knocking noise go? and what was causing it?? Just racking my brain trying to figure out what it was so I know for next time but I can't make sense of it... Really thought it was the rod bearing but it didn't make the noise at idle so I was questioning it...Luckily I kept searching!!
20230725_171507.mp4
-
By Ulfthednar
Just a quick test video while I'm learning to use my gopro (really, $250 discount I couldn't pass it up).
This is from my side drive to the top of the property.
The Dog loves the runs.
No snowflakes were injured in the production of this video.
https://youtu.be/tKjBFuHCkM0
-
COMMUNITY SECTIONS
ATV FORUMS
QUADCRAZY MEMBERSHIP
Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.