Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ATV Racing & ATV Events

Do you have an event or promotion you would like to share with everyone, post it here. ATV Racing events, jamborees, etc.

Subforums

  1. Post an ATV Event   (885 visits to this link)

    Post an atv event in the Main Community Events Section. Below you can post it in just the forums.

399 topics in this forum

    • 1 reply
    • 1,584 views
  1. North vs South MX Quad race

    • 1 reply
    • 1,550 views
  2. Hallstead VFC ATV Poker Run

    • 2 replies
    • 9,330 views
  3. TrailRex

    • 14 replies
    • 2,219 views
    • 0 replies
    • 830 views
    • 0 replies
    • 1,515 views
    • 0 replies
    • 1,258 views
  4. ATV Obstacross Racing

    • 1 reply
    • 1,519 views
    • 0 replies
    • 1,181 views
    • 0 replies
    • 1,285 views
    • 0 replies
    • 1,287 views
  5. Labor day atv races sept 4

    • 0 replies
    • 1,367 views
    • 0 replies
    • 993 views
    • 1 reply
    • 1,333 views
    • 4 replies
    • 1,330 views
  6. Just Add Dirt Events

    • 9 replies
    • 1,625 views
  7. Mehsa

    • 0 replies
    • 1,077 views
    • 14 replies
    • 3,449 views
    • 2 replies
    • 1,986 views
    • 0 replies
    • 1,220 views
  8. 2010 Adelanto Grand Prix

    • 24 replies
    • 3,991 views
  9. Atv cross country race, april 10

    • 1 reply
    • 1,324 views
    • 1 reply
    • 1,353 views
    • 2 replies
    • 1,127 views
  10. 8 Hour Team XC Race at The Motoplex

    • 0 replies
    • 1,171 views
    • 0 replies
    • 1,989 views
    • 0 replies
    • 1,295 views
    • 0 replies
    • 1,539 views
  11. atv ralley

    • 8 replies
    • 1,419 views
    • 1 reply
    • 1,768 views
    • 1 reply
    • 1,817 views
    • 2 replies
    • 1,665 views
  12. Atv stereos

    • 14 replies
    • 9,831 views
  13. Rnd 3 C.O.R.E. Desert Racing

    • 5 replies
    • 1,316 views
    • 2 replies
    • 1,524 views
    • 0 replies
    • 1,230 views
    • 0 replies
    • 1,298 views
    • 0 replies
    • 1,229 views
    • 0 replies
    • 1,200 views
  14. friday night drags

    • 0 replies
    • 1,347 views
    • 2 replies
    • 1,544 views
    • 2 replies
    • 1,459 views
  15. Colorado Offroad Extreme

    • 8 replies
    • 3,365 views
    • 0 replies
    • 1,458 views
    • 7 replies
    • 2,115 views
    • 0 replies
    • 1,148 views
    • 0 replies
    • 1,068 views
    • 0 replies
    • 1,208 views
    • 1 reply
    • 1,341 views
    • 0 replies
    • 1,228 views


  • Latest Forum Posts

    • Very good!  That air fuel screw is tapered and fits into an air passage in the carb, so turning the screw out increases the airflow. Some carburetors are different but most work this way.  Over time the screws tapered edge wears away and the adjustment gets less sensitive.   The optimal position where the engine is at max performance is usually done with the engine running. As you turn the screw in one direction or the other the engine revs higher or lower.  Higher is what your looking for the higher it revs the better the air fuel ratio is getting and you keep going in that direction until the engine starts to rev lower.  Thats the spot where  you stop and come back a hair. 
    • hilarious - i may take a pic of the pieces this time - it's not bogging as bad w/ air fuel screw not out as far. so let me make sense of this... they WHY behind it - and i likely will be thinking of this backward, but here it goes:  -the air fuel screw mixes air and gas --- if it's too far in (3 turns), meaning that i can see or almost see the tip of it in the cylinder wall, not enough AIR? is able to mix with the gas and create the explosion?  thus, backing it out to 2 turns, i cannot see the tip, this opens up the hole for more air to mix with the gas at a better ratio conducive to creating an explosion - this process is fine-tuned until there's not any bogging down (ie the best ratio has been reached for max performance).  ??
    • i only read the top part of your post on my phone - laptop showed me the rest - i'll tackle those steps next. i didn't have to loosen the throttle cable and other piece this time - was able to turn carb on its side to reset the air fuel screw - i backed it out from snug to 2 1/4 turns and the throttle went in almost half way - this is progress.  i may back it to 2 and see what it does just for kicks.  getting excited about this - will keep you posted
    • Bogging  is  more often  a  lean  problem than rich.. As Frank  said ,  I'd pull the carb once more  and  look for any tiny, and I mean  tiny   holes in the tubes  to the  jets . They  can be  missed very easily  because they're so  small  and  not a  brass jet  as  the  bigger ones  are . I  don't  know  if  your  carb  has the  holes  I'm  talking about  but  many  do.. Carbs  and fuel  mixture  settings  are  often accompanied by  a  lot  of  my  verbal  lubrication  here.  Sometimes I wish  I was multi-lingual  so  I'd  have  access to  a  broader range  of  "lubricant  " phrases. They're so  handy  when fiddling  with the small stuff  and  much  better to  use them than  start tossing  tools   LOL  

×
×
  • Create New...