Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ATV Racing & ATV Events

Do you have an event or promotion you would like to share with everyone, post it here. ATV Racing events, jamborees, etc.

Subforums

  1. Post an ATV Event   (885 visits to this link)

    Post an atv event in the Main Community Events Section. Below you can post it in just the forums.

399 topics in this forum

    • 1 reply
    • 1,693 views
    • 1 reply
    • 1,796 views
  1. NY/NJ/PA Group Ride!

    • 7 replies
    • 2,148 views
    • 0 replies
    • 1,180 views
  2. Oregon Dune Clean Up

    • 0 replies
    • 1,333 views
    • 0 replies
    • 1,594 views
    • 49 replies
    • 9,694 views
    • 7 replies
    • 2,016 views
  3. 2009 SDTA Dirt Track Schedule

    • 0 replies
    • 1,231 views
    • 0 replies
    • 1,338 views
    • 0 replies
    • 1,286 views
    • 0 replies
    • 1,178 views
  4. Rocky Mountain ATV Holiday Offer

    • 2 replies
    • 2,384 views
    • 0 replies
    • 2,072 views
    • 2 replies
    • 3,218 views
    • 7 replies
    • 1,571 views
    • 0 replies
    • 2,041 views
  5. Holler Crawlers 09 Event Schedule

    • 0 replies
    • 1,596 views
    • 0 replies
    • 1,649 views
    • 0 replies
    • 1,213 views
    • 0 replies
    • 1,387 views
  6. Loretta Lynn's Fall Ride

    • 4 replies
    • 1,783 views
  7. practice at Dirty South MX

    • 0 replies
    • 1,396 views
  8. practice at Dirty South MX

    • 0 replies
    • 1,505 views
  9. Ride for Samantha - Pennsylvania 1 2 3

    • 58 replies
    • 7,172 views
  10. 2008 Fall Powersports Expo

    • 0 replies
    • 1,377 views
    • 1 reply
    • 3,577 views
    • 0 replies
    • 1,117 views
  11. Ridegear.com Fall Promotion

    • 3 replies
    • 1,407 views
  12. ...a tough race weekend 1 2

    • 32 replies
    • 3,931 views
    • 1 reply
    • 1,424 views
    • 0 replies
    • 1,200 views
    • 0 replies
    • 1,476 views
    • 2 replies
    • 1,807 views
    • 3 replies
    • 2,333 views
    • 2 replies
    • 1,421 views
  13. Rocky Mountain ATV Specials

    • 23 replies
    • 3,676 views
    • 22 replies
    • 3,473 views
  14. Want a chance at $15,000??

    • 0 replies
    • 1,305 views
    • 10 replies
    • 2,339 views
    • 0 replies
    • 1,698 views
    • 4 replies
    • 2,261 views
  15. New mudbog event is July 4,5,6.

    • 0 replies
    • 1,298 views
    • 9 replies
    • 1,638 views
    • 0 replies
    • 1,839 views
    • 0 replies
    • 1,709 views
    • 2 replies
    • 1,307 views
    • 0 replies
    • 1,309 views
    • 16 replies
    • 2,432 views
    • 11 replies
    • 2,667 views


  • Latest Forum Posts

    • Very good!  That air fuel screw is tapered and fits into an air passage in the carb, so turning the screw out increases the airflow. Some carburetors are different but most work this way.  Over time the screws tapered edge wears away and the adjustment gets less sensitive.   The optimal position where the engine is at max performance is usually done with the engine running. As you turn the screw in one direction or the other the engine revs higher or lower.  Higher is what your looking for the higher it revs the better the air fuel ratio is getting and you keep going in that direction until the engine starts to rev lower.  Thats the spot where  you stop and come back a hair. 
    • hilarious - i may take a pic of the pieces this time - it's not bogging as bad w/ air fuel screw not out as far. so let me make sense of this... they WHY behind it - and i likely will be thinking of this backward, but here it goes:  -the air fuel screw mixes air and gas --- if it's too far in (3 turns), meaning that i can see or almost see the tip of it in the cylinder wall, not enough AIR? is able to mix with the gas and create the explosion?  thus, backing it out to 2 turns, i cannot see the tip, this opens up the hole for more air to mix with the gas at a better ratio conducive to creating an explosion - this process is fine-tuned until there's not any bogging down (ie the best ratio has been reached for max performance).  ??
    • i only read the top part of your post on my phone - laptop showed me the rest - i'll tackle those steps next. i didn't have to loosen the throttle cable and other piece this time - was able to turn carb on its side to reset the air fuel screw - i backed it out from snug to 2 1/4 turns and the throttle went in almost half way - this is progress.  i may back it to 2 and see what it does just for kicks.  getting excited about this - will keep you posted
    • Bogging  is  more often  a  lean  problem than rich.. As Frank  said ,  I'd pull the carb once more  and  look for any tiny, and I mean  tiny   holes in the tubes  to the  jets . They  can be  missed very easily  because they're so  small  and  not a  brass jet  as  the  bigger ones  are . I  don't  know  if  your  carb  has the  holes  I'm  talking about  but  many  do.. Carbs  and fuel  mixture  settings  are  often accompanied by  a  lot  of  my  verbal  lubrication  here.  Sometimes I wish  I was multi-lingual  so  I'd  have  access to  a  broader range  of  "lubricant  " phrases. They're so  handy  when fiddling  with the small stuff  and  much  better to  use them than  start tossing  tools   LOL  

×
×
  • Create New...