Quantcast
Jump to content

Recommended Posts

Posted

had spark lost spark found 2 wire that if i barly rub them together spark comes back but when i twist them together for solid contact spark go's away the wire that i found must have went to the switch that some one cut off the bike cause they lost the key the wires one is black with blue stripe and the other is the grond black if any one has one of these 4 wheelers could you please look at the wireing behind the switch and help me out or if you have the manual email me the wire diagram PLEASE!!!

  • 5 weeks later...
Posted

this thing is drivin me insane people i got a new complete wireing harness and key switch ,coil,battery the thing has a very weak spark the spark plug gap has to be set under.005 to get a spark ive even held on to the plug and it shocks me but nothin like it should and=y suggestion would be greatly appriciated thanks LOUIE SKIVERS:aargh::aargh::aargh::aargh:

Posted

Well it sounds to me like you are not getting a hot enough spark out of the coil.

Check all your cnnections and grounds (bolts to any frame connections)

Even though it's new, your coil or cdi could be defective.

You could have a bad plug wire, did you change that?

Posted

I moved this thread to the Polaris Tech section. Where it belongs! It is basically a repeat topic. Please do not repeat a thread . I have already merged this topic once. It makes it easier to see what responses you have recieved. That way you don't get repeat answers.

Posted
This is not a repeat thread i got the wireing strait this is another problem

icon8.gif Still need help with my boys scrambler 90

I GOT BRAND NEW WIRE HARNESS KEY SWITCH AND COIL AND CID CHECKED ALL THE GROUNDS BUT NOW I CANT GET A SPARK UNLESS THE GAP UN THE PLUG IS UNDER .005 ALLMOST SHUT COMPLETELY I HELD THE END OF PLUG BETWEEN MY FINGERS AND I SHOCKS ME BUT ONLY VERY MILD SHOCK KINDA LIKE A 9VOLT battery ON YOUR TOUNGE GETTIN PRETTY PISSED THE TOP END HAS BEEN COPLETELY REDONE AND WIREING IS ALL BRAND NEW ANY SUGGESTIONS WOULD BE GREAT THANKS LOUIE SKIVERSarghh.gifarghh.gifarghh.gifrealmad.gifrealmad.gif:rea lmad:

icon8.gifneed help with my boys scrambler 90

this thing is drivin me insane people i got a new complete wireing harness and key switch ,coil,battery the thing has a very weak spark the spark plug gap has to be set under.005 to get a spark ive even held on to the plug and it shocks me but nothin like it should and=y suggestion would be greatly appriciated thanks LOUIE SKIVERS

Looks like a repeat to me.

Posted

Agreed, you actually have three separate threads for the same issue. They have all been merged into the first thread you started. I understand that your situation has progressed, but it is still the same issue. Also, you also have said essentially the same thing in three separate posts. I deleted two of those. Please try not to repeat yourself. It is easier for every one if you keep things clean and consolidated.

  • 11 months later...
Posted

did you ever figure out the problem with your son's quad? We are having the same problems, we're not getting any spark, we have replaced the spark plug. Still nothing. And advice or suggestions will help.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By TomJulio
      My 1992 TRX00 recently stopped firing.  I understand this is a common problem. I have ordered an aftermarket CDI unit.    TJ
    • By Callaway
      I am trying to diagnose a no spark issue with my 02 Big Bear 400 and I am really hoping it is not a CDI.  I have done the test on the stator and I believe that is faulty.  I ordered a new aftermarket one from a the jungle website and it tested bad right out of the box so I am waiting for a different one to arrive from an ATV parts supplier.  I started looking out of curiosity at CDI units and it seems if it is for a big bear you are SOL.  Kodiaks, no problem.  Big Bear. No such luck.  
    • Guest
      By Guest
      Hey all, new to the forum! I just bought a 1998 Kawasaki bayou 300, 4x4 not running. Initially I found no spark. Ended up playing with the plug wire (made sure plug top and wiring was touching) and got spark yesterday and the quad fired up off ether. Come to work on it today and now no spark again. Before I got spark and now today if I touch the plug after cranking I get shocked, and it will spark after I release the starter button. I was jumping the quad with a freshly charged car battery that has 12v while cranking. Cleaned out the kill switch and ignition button. All looks good. Purchased new plugs. They're are a lot of wires cut/ disconnected. But shouldn't matter if I got spark without them connected... 
    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By Louznmemind
      I know this is a stupid question but here I am.. I'm wanting to have the ability to disable my taillight/brake light on my '96 Polaris Xpress at will, it comes on with the key and there are times I don't want it to illuminate. I have basic wiring knowledge and I'd like to put a toggle switch to disable it. I'm not sure of the wiring setup on this thing, can I just use a toggle switch on the ground wire to kill it when I choose? Can someone clarify which wire I need to work with and the easiest way? Excuse my ignorance yall.
×
×
  • Create New...