Quantcast
Jump to content

kp3004x4

Members
 View Profile  See their activity

  • Posts

    164

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by kp3004x4

  1. kp3004x4
  2. kp3004x4
    Yes sir the key switch itself. Easy to check if you can get to back of it. With a multimeter or even a pen light. Should have a definite on off with light or voltage of some kind when switching the key to on or off.
  3. kp3004x4
    Interesting????
  4. kp3004x4
    Yes sir. That book dude has lost touch,mech would be right on all things. Spot on
  5. kp3004x4
    I have seen this problem before and it ended up being the switch itself burnt out. Do what mech said and test all then test switch itself to see if you are getting power to it if so then look at switch for problem. Hope this helps
  6. kp3004x4
    Yes mech, exhaust could be blocked air has to go somewhere if not getting in or out. Just like when in high school putting a banana in a tail pipe. Or putting duels on a car for more air flow might be?
  7. kp3004x4
    You shouldn't pick sides just you know what you have no one else does. I myself don't care what people think I know me you know you they know them. But I have over 30 years of mechanical so doesn't matter. Just learning what you find out yourself is the better answer to all. I myself have come across allot of crap and people that always knows best but. You need to do you. Drs say I might eventually die. I'm only on here to help out since my body's giving up. Hope for the best for all . ✌️ I myself still learning!
  8. kp3004x4
    Sounds to me like bushing is biding somewhere at cover. Do you have washer before bushing and after?? Sounds like biding hard at this point could be around but seems by post
  9. kp3004x4
    Ok see if the air box inlet is clogged up or the filter is there should be and inlet that lets air to air filter behind air filter I have seen this problem many a times. Kids run em in mud then mud clogs air inlet a bit if when you take the air cover off it runs then you need more air for carburetor to do its job. Try running it without air filter. Maybe bad also. Carbs need the correct air fuel ratio to run. And it kinda looks this way. And mech don't let this fellow get under your skin. Sounds like he's reading from a book anyhow. Takes experience and it doesn't show. Y'all be safe.
  10. kp3004x4
    I would adjust the oil to seasons yes if real hot ,ask local mechanics in your area,I would ask a good shade tree mechanic because they would definitely know more than most dealers and for the most part was sent to school for a particular bike and not all bikes are particularly the same even two of the same make and model something will be different,just get out there and get grease on your hands and never give up. Like that old school house rock cartoons, knowledge is power. Have fun
  11. kp3004x4
    Welcome LS_noma
  12. kp3004x4
    Yes sir, sitting on 11 acre's now with view of the hills of the Ozarks,with hunting club/ forest all around. Life is good, maybe a beer in my hand every now and then and my pipe with cheery tobacco can't beat it.
  13. kp3004x4
    I traded two quads and 100 dollars for a old 1976 ford school bus I'm fixing it up on side for a getaway look out there have seen many that you can get cheap and could live in it until you get something lots of property in the woods and mostly if people know you can work on them they will come, install solar on that bad boy and you got something. Good luck
  14. kp3004x4
    If bike is older CHK to make sure your frame is solid, especially around joints ,have seen some that looked ok but had gotten water inside of frame and rotted itself from inside out. Most likely from owner putting it intentionally in water all the time thinking it's a boat.
  15. kp3004x4
    Most likely what mech said is the o ring is gone ,but not to hard of a job to fix or expensive.
  16. kp3004x4
    Looks like carb is messed up not letting the needle slid evenly up and down,also doesn't look like needle is set so that it goes down,what do all of you think?
  17. kp3004x4
    Agree with you on that mech the bearings around most cranks need good oil flow. Like on some the flow goes out to the pull rope even I have seen in the past. Also never flush one because it might interfere with the special coating and even if you put new oil in ,the bearings will be not until heated to a point that the metal will soaks it back up.
  18. kp3004x4
    Some bed liners might just work but I'd make sure about what adhesive that is in it doesn't melt the plastic after awhile.good idea
  19. kp3004x4
    Yes sir gf can do that you especially if they're wearing next to nothing on. Done somethings the same in the past. You live you learn as grandpa used to say.
  20. kp3004x4
    15/40 of your choice just be sure to run after change at idle then CHK again to make sure it's full
  21. kp3004x4
    Watched a video the other day on polishing plastic he used an aluminum polishing stick with high speed buffing wheel on a grinder that could be set at 3000 rpm. Haven't tried it myself but he fixed all the plastic on an old quad to like new condition and didn't take long even did a windshield to a side x side.
  22. kp3004x4
    Yes kinda sounds like a low voltage issue try cleaning the battery terminals and make sure everything has a good ground
  23. kp3004x4
    Sure would have seen that before
  24. kp3004x4
    Can't find the rag it's dark
  25. kp3004x4
    Always reset air jets on new carbs,one and a 1/4 out after turning in just to seat ,try with that first then slowly turn in or out till tunes out. Hope for the best. And also could be starving for fuel with two fuel filters in place some of them cheaper carbs are finicky.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...