06kfx440
-
Posts
454 -
Joined
-
Last visited
-
Days Won
19
Content Type
Profiles
Forum
Gallery
ATV Magazine
Events Calendar
Downloads
Store
Community Map
Everything posted by 06kfx440
-
I took my kfx out and it didn't sound right. Besides bouncing off the rev limiter, does it sound right to you? Sent from my SM-N920V using Tapatalk
-
Is this an auto-clutch. If so. You will have to replace the clutch. Or adjust it past the manual spec. I had the same problem on my banshee. Manual clutch tho. Sent from my SM-N920V using Tapatalk
-
Any luck? Sent from my SM-N920V using Tapatalk
-
Confusis say, He who farts in church, must sit in pue. [emoji58] Sent from my SM-N920V using Tapatalk -
I agree. I can pull big wires thru conduit with synthetic rope. The only downfall that I've seen is when you coil it up, It takes form of the wind. When you uncoil and in the relaxed position it winds back to that form. Sent from my SM-N920V using Tapatalk That's why I use climbers rope. It won't bind up Sent from my SM-N920V using Tapatalk
-
What I did was take the 1/4 cable and replaced it with a high tinsel rope. I didn't find it at harbor freight but I used a climbers robe because even if a pulley bearing seizes it will still go up and down and be okay. If I remember. I went to atomicclimbingholds.com Sent from my SM-N920V using Tapatalk
-
I have teen agers and shovels. Hasn't let me down yet. Lol But on a serious note, I use synthetic rope as well. Just for the spring back if it breaks with steel cable. Had that happen to my hand on a tow truck. Not pretty. Still going strong for 5 years. Sent from my SM-N920V using Tapatalk
-
1997 Kawasaki Bayou 300 2x4 (klf300b) Runs Bad
06kfx440 replied to JacobSlabach's topic in Kawasaki ATV Forum
Could be that your rockers are worn down. They might be okay in one spot and way off in another. Sent from my SM-N920V using Tapatalk -
As far as running slow. Adjust the idle screw on the carb. Sent from my SM-N920V using Tapatalk
-
Oil the filter when your done blowing out the air filter. AutoZone or comparable should have the oil for it. Sent from my SM-N920V using Tapatalk Check for air leaks. And screw in your idle screw to get the rpms up Sent from my SM-N920V using Tapatalk
-
Try to adjust the clutch cable. It should be on the lever where the clutch lever is. If that doesn't make any difference. Trace the cable to where it sits on the motor. There should be a arm looking thing on top of the motor. If you closely inspect. The arm should have a point on it and one on the motor. They should be in line. If all else checks out. You need a new clutch Sent from my SM-N920V using Tapatalk
-
Loading Ramps Quadboss Pit Posse Yutrax
06kfx440 replied to r97f1504x4's topic in General ATV Discussion
I know trucks are easier to get around. But even with a truck I've used a small trailer. I have 2 actually. A 4x6 and a 7x10. But as far as loading them, I've used nothing but a 2x6 with grips and feet Sent from my SM-N920V using Tapatalk -
Never mind. I'm using hids instead. Sent from my SM-N920V using Tapatalk
-
I need the headlight harness that goes to the headlights. Not the housing. Sent from my SM-N920V using Tapatalk
-
I have the same exact charger as picture 2. It charges the Harleys and my quads and go cart with no issues. Great buy for me. I bought the plug in accessory that bolts onto the battery. Easy to just disconnect and reconnect Sent from my SM-N920V using Tapatalk
- 67 replies
-
- 1
-
-
- battery
- trickle charger
- (and 1 more)
-
I need to do that to my trailer. The one I have just flops in the breeze when it's empty. But tractor supply is what it is. I'll need to add a v in the front for stability as well. Spring welding for me. Sent from my SM-N920V using Tapatalk
-
Donuts in the snow make it fun for my youngest Sent from my SM-N920V using Tapatalk
-
The Official Good morning thread!
06kfx440 replied to BuckBilly's topic in General Talk - Anything Goes!
Morning everyone. Had a late night. Muscle spasms suck! Sent from my SM-N920V using Tapatalk -
I have 3 feet to my property line and the village I live in doesn't allow building anything on or close to that line. I do agree with a form build then block but I'd be taking away from my driveway. So brick is the way to go? Sent from my SM-N920V using Tapatalk And item 4 or 1/2" stone? Sent from my SM-N920V using Tapatalk
-
See. I would use block. It's inexpensive and easy to work with. But over time block disintegrates. Same with rail road ties. That's why I was thinking interlock bricks. But if you feel it would hold out for 20+ years. I'm all for it. I know that drainage is key and I believed that it was done. Until I ran a snake thru the drainage exit and it stopped 10 feet in. Would I have to use a vibrator to ensure the cement travels to the bottom? Sent from my SM-N920V using Tapatalk
-
I have a job to to. My retaining wall collapsed and was all over my driveway. This happened about a week ago. The previous owner had it installed. They used 6"x4" block that was glued together. It's approximately 4' high and 70' long. To my knowledge they should have used 12"x8" interlocking bricks that needed bracing to go into the hill behind it. My insurance company will cover the cost of material and labor. But I've done this before and if I can make some money on it, then why not diy. Any thoughts on what to use Sent from my SM-N920V using Tapatalk
-
Welcome to quadcrazy. There are plenty of member that know alot of useful information. If it once ran. One of us can fix it. So don't be shy to ask questions. The only stupid question is the one that isn't asked. Sent from my SM-N920V using Tapatalk
-
Try knmparts.com. they have a bunch of useful stuff for the gy6 motors. All different sizes too. Sent from my SM-N920V using Tapatalk
-
Educational. Not my first choice of brand but definitely interesting. I feel that video is focused on the new king quad. I'd like to see the entire history of all machines. Sent from my SM-N920V using Tapatalk
