mikeexplorer

Agreed, sounds like your like me, old school. Been on fourm boards for years, but over the past few years social media has taken over and many have shut down for lack of use. I still prefer the fourm boards over social media because its organized better, with groups and topics. Social media tends to be like spaghetti of posts and nonsense. I have also seen how people have changed because of social media. They will post a question, then like 2 hours later, post a reply like "What? Nobody has an answer for me?" They don't get it how it works. They want the "instant gratification" of social media verses the fourm boards. Mike

I only have worked on Arctic Cats but I found the electrical diagrams to be straightforward and easy to follow. Color coding of the wires makes it easy to find the right one and its well documented in the schematic. Ive used the service manuals as well and find them to be written well with the included pictures. Part diagrams online are easy to follow and depending on what I need, sometimes I buy OEM, sometimes i buy aftermarket. Some parts are best bought OEM such as the drive belt. Its more money but they last much longer then any aftermarket belt. Mike

Usually its the first Sunday in October, all dependent on the landowners. Mike

They usually get around 350 - 425 machines for the ride. Takes about 3 hours to do the course with stops for drawing cards. Mostly technical in the woods riding. It is their largest fundraiser for the year.

The video is not mine and not the Hallstead ride. The Hallstead ride is on all private land and is only open for the day of the event. They do have a huge mud pit as part of the course and I swamped a machine in it once. Mike

We did, aside from it being a good fundraiser for the fire company, the course is always a nice technical in the woods route. I have volunteered to help them for several years now since they do not have enough members in the hose company to handle the crowd they get. Mike

Thanks for adding the manual, there are quite a few already uploaded here, two other sources for manuals can be found here https://support.countrycat.com/?feed=recent https://www.mymowerparts.com/pdf/Arctic-Cat-ATV-Repair-and-Service-Manuals/ This is a procedure I use to print out the schematics The diagrams don't print well on a regular sheet of paper due to their size so here is a procedure to get the diagram you need and make a nice print. This will be with utilities you can get for free (the best kind After downloading the large PDF of the schematics, go to this website here... Tracker Software Products :: PDF-XChange Viewer, Free PDF Reader Download pdf-xchange (its free) Open the pdf file with this program. by clicking on the selections you can get to the exact schematic you need. Once its displayed do this: File -> Export -> Export to Image Select "Current page" , Image type "JPEG", choose your folder to drop the image, give it a name like "2006 400 auto" set page zoom to 100% and resolution to 300 or 400 dpi Then click export. You will now have a JPG of the page. Next step is to go to this website... https://www.posteriza.com/www.posteriza.com/es/index380c.html?lang=en_US Download the program (free) What this will do is allow you to tke this large JPG and break it up onto several pages. I use 4 for the schematics. Its pretty easy to follow and I print them without a border. Print them out and use an old fashioned "cut & tape" and you will now have a nice large printout of your schematic. Usually 4 page print is enough to make the diagram readable. Mike

I have owned Arctic Cats, I did have a Kymco Mongoose for a few years for the girl to ride, we sold it to a friend and it is still in use today. The smaller Arctic Cats of the time were Kymco based, Her first utility machine was basically a Kymco MXU, its 8 years old now, almost 10,000 miles on it and still runs well. I upgraded her to an Alterra so we kept the other machine as a backup and I use it for plowing. Mike

I own Arctic Cats and like that they have a 2 inch receiver and an accessory plug under the rear fender for either a battery tender or for any pull behind machine that would need power. My first one I had for 10 years and put 16,000 miles on it then sold it to a friend for parts. Mike

The smaller Arctic Cats have clutch spacers that can be removed if you want more speed. Mike

That came out nice, she is really going to enjoy it.

Easy check for a bad coil is when it is hot, pull the plug and check spark. bad plug can be the issue. Is it getting too hot? Like fan not running? Under the seat is the solenoid for the starter, jump it with a screwdriver to see if the starter turns. If you have a battery jump box, disconnect winch and apply power directly to it to see if the winch itself is working. If it is, its the winch solenoid that is bad. Mike

I had a similar noise and it was the heat shield. I put a hose clamp around it and the noise stopped. Mike

I owned a Mongoose 250 for a few years and sold it in 2010, it is still in use today. Most of the smaller bore Arctic Cats used Kymco engines. One I own is the 2010 366 with over 9,000 miles on it and still runs fine. This is very similar to the MXU and some parts cross between the machines (such as the shocks and suspension system. Mike

2013 manual is here https://support.countrycat.com/posts/2807051-2013-450-atv-service-manual

You can find parts for the 1999 Arctic Cat at www.countrycat.com

Got to use it the past weekend at the Hallstead ATV Poker run. Worked well

Haven't heard back from him with my suggestions.

I bought one of these this year, so far have not had to use it.

I bought a RAM mount for my obsolete Garmin GPS unit and it has worked very well. This is for the vehicle, not the quad. Mike

The link I posted in the Arctic Cat forum, you can use it to compare part numbers for different year machines to see if they are the same

You can still find parts here https://www.countrycat.com/

It was modified by the trial lawyers making it pretty useless. PaOHV is trying again to push this

Welcome, I am from the Northeast PA area

What Ajmboy was referring to was the post. This website has a lot of technical resources available for the users of the site. Its a website and unlike social media, you don't get an instant response. Those who have the resources to share are only here on their spare time so a reply may be a day or two. Plus the way it was posted "I am just here to get a manual" is outright saying "once I get this manual, im gone" I wouldn't be too inclined to help that person either. Then on top of that to post 10 replies with only a number is childish, another reason to not help them either. A forum board is a community. There is already a lot of people who do come here to ask a question about a problem, then someone provides some suggestions to help solve it, and they never post back that it fixed the problem, so we never know if our suggestions worked. We assume it did, because otherwise they would post back that it didn't work. Mike